ADBMS1818ASWZ-R7 datasheet(11/89 Pages) AD

11 / 89 page

Data Sheet

ADBMS1818

PIN CONFIGURATION AND FUNCTION DESCRIPTIONS

analog.com

Rev. 0 | 11 of 89

Figure 3. Pin Configuration

Table 12. Pin Function Descriptions

Pin No.

Mnemonic

Description

V+

Positive Supply Pin.

2, 4, 6, 8, 10, 12,

14, 16, 18, 20, 22,

24, 26, 28, 30, 32,

34, 36, 38

C0 to C18

Cell Inputs.

3, 5, 7, 9, 11, 13,

15, 17, 19, 21, 23,

25, 27, 29, 31, 33,

35, 37

S1 to S18

Balance Inputs/Outputs. 18 internal N-channel metal-oxide semiconductor field effect transistors (MOSFETs) are connected between

S(n) and C(n–1) for discharging cells.

39 to 47

GPIO1 to GPIO9

General Purpose I/O. GPIO1 to GPIO9 can be used as digital inputs or digital outputs or as analog inputs with a measurement range

from V– to 5 V. GPIO3, GPIO4, and GPIO5 can be used as I2C or SPI ports.

VREG

5 V Regulator Input. Bypass with an external 1 μF capacitor.

DRIVE

Connect the base of an NPN transistor to the DRIVE pin. Connect the collector to V+ and the emitter to VREG.

VREF2

Buffered 2nd Reference Voltage for Driving Multiple 10 kΩ Thermistors. Bypass with an external 1 μF capacitor.

VREF1

ADC Reference Voltage. Bypass with an external 1 μF capacitor. No dc loads allowed.

DTEN

Discharge Timer Enable. Connect DTEN to VREG to enable the discharge timer.

53, 54, 61, 62

SDI, SDO, CSB,

SCK

4-Wire SPI. Active low chip select (CSB), serial clock (SCK), and serial data in (SDI) are digital inputs. Serial data out (SDO) is an

open drain NMOS output pin. SDO requires a 5 kΩ pull-up resistor.

ISOMD

Serial Interface Mode. Connecting ISOMD to VREG configures Pin 53, Pin 54, Pin 61, and Pin 62 of the ADBMS1818 for 2-wire isoSPI

mode. Connecting ISOMD to V– configures the ADBMS1818 for 4-wire SPI mode.

WDT

Watchdog Timer Output Pin. This is an open drain negative metal-oxide semiconductor (NMOS) digital output. WDT can be left

disconnected or connected with a 1 M resistor to VREG. If the ADBMS1818 does not receive a valid command within 2 seconds, the

watchdog timer circuit resets the ADBMS1818 and the WDT pin goes high impedance.

IBIAS

Isolated Interface Current Bias. Tie IBIAS to V– through a resistor divider to set the interface output current level. When the isoSPI

interface is enabled, the IBIAS pin voltage is 2 V. The IPA and IMA or IPB and IMB output current drive is set to 20 times the current,

IB, sourced from the IBIAS pin.

ADBMS1818ASWZ-R7 数据表(PDF) 11 Page - Analog Devices

ADBMS1818ASWZ-R7 数据表(HTML) 11 Page - Analog Devices

Html Pages

1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 41 42 43 44 45 46 47 48 49 50 51 52 53 54 55 56 57 58 59 60 61 62 63 64 65 66 67 68 69 70 71 72 73 74 75 76 77 78 79 80 81 82 83 84 85 86 87 88 89

数据表下载