MPC8541ECVTALF datasheet(50/84 Pages) FREESCALE

50 / 84 page

MPC8541E PowerQUICC™ III Integrated Communications Processor Hardware Specifications, Rev. 4

Freescale Semiconductor

I2C

12.2

I2C AC Electrical Specifications

Table 40 provides the AC timing parameters for the I2C interface of the MPC8541E.

Table 40. I2C AC Electrical Specifications

All values refer to VIH (min) and VIL (max) levels (see Table 39).

Parameter

Symbol 1

Min

Max

Unit

SCL clock frequency

fI2C

400

kHz

Low period of the SCL clock

tI2CL

1.3

—

μs

High period of the SCL clock

tI2CH

0.6

—

μs

Setup time for a repeated START condition

tI2SVKH

0.6

—

μs

Hold time (repeated) START condition (after this period, the first clock

pulse is generated)

tI2SXKL

0.6

—

μs

Data setup time

tI2DVKH

100

—

Data hold time:

CBUS compatible masters

I2C bus devices

tI2DXKL

—

0 2

—

0.9 3

μs

Rise time of both SDA and SCL signals

tI2CR

20 + 0.1 Cb

300

Fall time of both SDA and SCL signals

tI2CF

20 + 0.1 Cb

300

Set-up time for STOP condition

tI2PVKH

0.6

—

μs

Bus free time between a STOP and START condition

tI2KHDX

1.3

—

μs

Noise margin at the LOW level for each connected device (including

hysteresis)

VNL

0.1

× OV

—V

Noise margin at the HIGH level for each connected device (including

hysteresis)

VNH

0.2

× OV

—V

Notes:

1. The symbols used for timing specifications herein follow the pattern of t(first two letters of functional block)(signal)(state) (reference)(state)

for inputs and t(first two letters of functional block)(reference)(state)(signal)(state) for outputs. For example, tI2DVKH symbolizes I

2C timing

(I2) with respect to the time data input signals (D) reach the valid state (V) relative to the tI2C clock reference (K) going to the

high (H) state or setup time. Also, tI2SXKL symbolizes I

2C timing (I2) for the time that the data with respect to the start

condition (S) went invalid (X) relative to the tI2C clock reference (K) going to the low (L) state or hold time. Also, tI2PVKH

symbolizes I2C timing (I2) for the time that the data with respect to the stop condition (P) reaching the valid state (V) relative

to the tI2C clock reference (K) going to the high (H) state or setup time. For rise and fall times, the latter convention is used

with the appropriate letter: R (rise) or F (fall).

MPC8541E provides a hold time of at least 300 ns for the SDA signal (referred to the VIHmin of the SCL signal) to bridge the

undefined region of the falling edge of SCL.

3. The maximum tI2DVKH has only to be met if the device does not stretch the LOW period (tI2CL) of the SCL signal.

4. CB = capacitance of one bus line in pF.

5. Guaranteed by design.

MPC8541ECVTALF 数据表(PDF) 50 Page - Freescale Semiconductor, Inc

MPC8541ECVTALF 数据表(HTML) 50 Page - Freescale Semiconductor, Inc

Html Pages

1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 41 42 43 44 45 46 47 48 49 50 51 52 53 54 55 56 57 58 59 60 61 62 63 64 65 66 67 68 69 70 71 72 73 74 75 76 77 78 79 80 81 82 83 84

数据表下载