PIC18F258-ESLASHSOSQTP datasheet(98/402 Pages) MICROCHIP

98 / 402 page

PIC18FXX8

DS41159E-page 96

9.2

PORTB, TRISB and LATB

Registers

PORTB is an 8-bit wide, bidirectional port. The corre-

sponding Data Direction register is TRISB. Setting a

TRISB bit (= 1) will make the corresponding PORTB

pin an input (i.e., put the corresponding output driver in

a high-impedance mode). Clearing a TRISB bit (= 0)

will make the corresponding PORTB pin an output (i.e.,

put the contents of the output latch on the selected pin).

Read-modify-write operations on the LATB register,

read and write the latched output value for PORTB.

EXAMPLE 9-2:

INITIALIZING PORTB

Each of the PORTB pins has a weak internal pull-up. A

single control bit can turn on all the pull-ups. This is

performed by clearing bit RBPU (INTCON2 register).

The weak pull-up is automatically turned off when the

port pin is configured as an output. The pull-ups are

disabled on a Power-on Reset.

Four of the PORTB pins (RB7:RB4) have an interrupt-

on-change feature. Only pins configured as inputs can

cause this interrupt to occur (i.e., any RB7:RB4 pin

configured as an output is excluded from the interrupt-

on-change comparison). The input pins (of RB7:RB4)

are compared with the old value latched on the last

read of PORTB. The “mismatch” outputs of RB7:RB4

are ORed together to generate the RB Port Change

Interrupt with Flag bit RBIF (INTCON register).

This interrupt can wake the device from Sleep. The

user, in the Interrupt Service Routine, can clear the

interrupt in the following manner:

Any read or write of PORTB (except with the

MOVFF

instruction). This will end the mismatch

condition.

Clear flag bit RBIF.

A mismatch condition will continue to set flag bit RBIF.

Reading PORTB will end the mismatch condition and

allow flag bit RBIF to be cleared.

The interrupt-on-change feature is recommended for

wake-up on key depression operation and operations

where PORTB is only used for the interrupt-on-change

feature. Polling of PORTB is not recommended while

using the interrupt-on-change feature.

CLRF

PORTB

; Initialize PORTB by

; clearing output

; data latches

CLRF

LATB

; Alternate method

; to clear output

; data latches

MOVLW

0CFh

; Value used to

; initialize data

; direction

MOVWF

TRISB

; Set RB3:RB0 as inputs

; RB5:RB4 as outputs

; RB7:RB6 as inputs

Note 1: While in Low-Voltage ICSP mode, the

RB5 pin can no longer be used as a

general purpose I/O pin and should not

be held low during normal operation to

protect against inadvertent ICSP mode

entry.

2: When using Low-Voltage ICSP Program-

ming (LVP), the pull-up on RB5 becomes

disabled. If TRISB bit 5 is cleared,

thereby setting RB5 as an output, LATB

bit 5 must also be cleared for proper

operation.

PIC18F258-E/SOSQTP 数据表(PDF) 98 Page - Microchip Technology

PIC18F258-E/SOSQTP 数据表(HTML) 98 Page - Microchip Technology

Html Pages

1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 41 42 43 44 45 46 47 48 49 50 51 52 53 54 55 56 57 58 59 60 61 62 63 64 65 66 67 68 69 70 71 72 73 74 75 76 77 78 79 80 81 82 83 84 85 86 87 88 89 90 91 92 93 94 95 96 97 98 99 100 ...More

数据表下载