PIC18F258-ESLASHSOSQTP datasheet(151/402 Pages) MICROCHIP

151 / 402 page

DS41159E-page 149

PIC18FXX8

17.3.6

SLAVE MODE

In Slave mode, the data is transmitted and received as

the external clock pulses appear on SCK. When the

last bit is latched, the SSPIF interrupt flag bit is set.

While in Slave mode, the external clock is supplied by

the external clock source on the SCK pin. This external

clock must meet the minimum high and low times as

specified in the electrical specifications.

While in Sleep mode, the slave can transmit/receive

data. When a byte is received, the device will wake-up

from Sleep. Before enabling the module in SPI Slave

mode, the clock line must match the proper Idle state.

The clock line can be observed by reading the SCK pin.

The Idle state is determined by the CKP bit

(SSPCON1<4>).

17.3.7

SLAVE SELECT

SYNCHRONIZATION

The SS pin allows a Synchronous Slave mode. The

SPI must be in Slave mode with SS pin control enabled

(SSPCON1<3:0> = 04h). The pin must not be driven

low for the SS pin to function as an input. The data latch

must be high. When the SS pin is low, transmission and

reception are enabled and the SDO pin is driven. When

the SS pin goes high, the SDO pin is no longer driven,

even if in the middle of a transmitted byte and becomes

a floating output. External pull-up/pull-down resistors

may be desirable depending on the application.

When the SPI module resets, the bit counter is forced

to ‘0’. This can be done by either forcing the SS pin to

a high level or clearing the SSPEN bit.

To emulate two-wire communication, the SDO pin can

be connected to the SDI pin. When the SPI needs to

operate as a receiver, the SDO pin can be configured

as an input. This disables transmissions from the SDO.

The SDI can always be left as an input (SDI function)

since it cannot create a bus conflict.

FIGURE 17-4:

SLAVE SYNCHRONIZATION WAVEFORM

Note 1: When the SPI is in Slave mode with SS pin

control enabled (SSPCON1<3:0> = 0100),

the SPI module will reset if the SS pin is set

to VDD.

2: If the SPI is used in Slave mode with CKE

set, then the SS pin control must be

enabled.

SCK

(CKP = 1

SCK

(CKP = 0

Input

Sample

SDI

bit 7

SDO

bit 7

bit 6

bit 7

SSPIF

Interrupt

(SMP = 0)

CKE = 0)

(SMP = 0)

Write to

SSPBUF

SSPSR to

SSPBUF

Flag

bit 0

bit 7

bit 0

Next Q4 cycle

after Q2

↓

PIC18F258-E/SOSQTP 数据表(PDF) 151 Page - Microchip Technology

PIC18F258-E/SOSQTP 数据表(HTML) 151 Page - Microchip Technology

Html Pages

1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 41 42 43 44 45 46 47 48 49 50 51 52 53 54 55 56 57 58 59 60 61 62 63 64 65 66 67 68 69 70 71 72 73 74 75 76 77 78 79 80 81 82 83 84 85 86 87 88 89 90 91 92 93 94 95 96 97 98 99 100 ...More

数据表下载

链接网址

PIC18F258-E/SOSQTP 数据表(PDF) 151 Page - Microchip Technology

PIC18F258-E/SOSQTP 数据表(HTML) 151 Page - Microchip Technology

Html Pages

1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 41 42 43 44 45 46 47 48 49 50 51 52 53 54 55 56 57 58 59 60 61 62 63 64 65 66 67 68 69 70 71 72 73 74 75 76 77 78 79 80 81 82 83 84 85 86 87 88 89 90 91 92 93 94 95 96 97 98 99 100 ...More

数据表 下载

链接网址

数据表下载