ADE7166 datasheet(91/144 Pages) AD

91 / 144 page

ADE7566/ADE7569/ADE7166/ADE7169

Rev. A | Page 91 of 144

INTERRUPT FLAGS

The interrupt flags and status flags associated with the interrupt vectors are shown in Table 72 and Table 73. Most of the interrupts have

flags associated with them.

Table 72. Interrupt Flags

Interrupt Source

Flag

Bit Address

Description

IE0

TCON.1

IE0

External Interrupt 0.

TF0

TCON.5

TF0

Timer 0.

IE1

TCON.3

IE1

External Interrupt 1.

TF1

TCON.7

TF1

Timer 1.

SCON.1

Transmit Interrupt.

RI + TI

SCON.0

Receive Interrupt.

T2CON.7

TF2

Timer 2 Overflow Flag.

TF2 + EXF2

T2CON.6

EXF2

Timer 2 External Flag.

ITEMP (Temperature ADC)

Temperature ADC Interrupt. Does not have an interrupt flag associated with it.

IPSM (Power Supply)

IPSMF.6

FPSM

PSM Interrupt Flag.

IADE (Energy Measurement DSP)

MIRQSTL.7

Read MIRQSTH, MIRQSTM, MIRQSTL.

Table 73. Status Flags

Interrupt Source

Flag

Bit Address

Description

ITEMP (Temperature ADC)

Temperature ADC Interrupt. Does not have a status flag associated with it.

SPI2CSTAT

SPI Interrupt Status Register.

ISPI/I2CI

SPI2CSTAT

I2C Interrupt Status Register.

TIMECON.7

RTC Midnight Flag.

IRTC (RTC Interval Timer)

TIMECON.2

RTC Alarm Flag.

WDT (Watchdog Timer)

WDCON.2

WDS

Watchdog Timeout Flag.

A functional block diagram of the interrupt system is shown in

Figure 88. Note that the PSM interrupt is the only interrupt in

the highest priority level.

If an external wake-up event occurs to wake the ADE7566/

ADE7569/ADE7166/ADE7169 from PSM2, a pending external

interrupt is generated. When the EX0 or EX1 bit in the Interrupt

Enable SFR (IE, 0xA8) is set to enable external interrupts, the

program counter is loaded with the IE0 or IE1 interrupt vector.

The IE0 and IE1 interrupt flags in the TCON register are not

affected by events that occur when the 8052 MCU core is shut

down during PSM2. See the Power Supply Monitor Interrupt

(PSM) section.

The RTC, temperature ADC, and I2C/SPI interrupts are latched

such that pending interrupts cannot be cleared without entering

their respective interrupt service routines. Clearing the RTC

midnight flags and alarm flags does not clear a pending RTC

interrupt. Similarly, clearing the I2C/SPI status bits in the SPI

Interrupt Status SFR (SPISTAT, 0xEA) does not cancel a

pending I2C/SPI interrupt. These interrupts remain pending

until the RTC or I2C/SPI interrupt vectors are enabled. Their

respective interrupt service routines are entered shortly

thereafter.

Figure 88 shows how the interrupts are cleared when the

interrupt service routines are entered. Some interrupts with

multiple interrupt sources are not automatically cleared;

specifically, the PSM, ADE, UART, and Timer 2 interrupt

vectors. Note that the INT0 and INT1 interrupts are only

cleared if the external interrupt is configured to be triggered by

a falling edge by setting IT0 in the Timer/Counter 0 and

Timer/Counter 1 Control SFR (TCON, 0x88). If INT0 or INT1

is configured to interrupt on a low level, the interrupt service

routine is reentered until the respective pin goes high.

ADE7166 数据表(PDF) 91 Page - Analog Devices

ADE7166 数据表(HTML) 91 Page - Analog Devices

Html Pages

1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 41 42 43 44 45 46 47 48 49 50 51 52 53 54 55 56 57 58 59 60 61 62 63 64 65 66 67 68 69 70 71 72 73 74 75 76 77 78 79 80 81 82 83 84 85 86 87 88 89 90 91 92 93 94 95 96 97 98 99 100 ...More

数据表下载