ATmega169PV-8MCH datasheet(113/393 Pages) ATMEL

113 / 393 page

113

8018N–AVR–08/09

ATmega169P

The Timer/Counter Overflow Flag (TOV1) is set according to the mode of operation selected by

the WGM13:0 bits. TOV1 can be used for generating a CPU interrupt.

15.6

Input Capture Unit

The Timer/Counter incorporates an Input Capture unit that can capture external events and give

them a time-stamp indicating time of occurrence. The external signal indicating an event, or mul-

tiple events, can be applied via the ICP1 pin or alternatively, via the analog-comparator unit. The

time-stamps can then be used to calculate frequency, duty-cycle, and other features of the sig-

nal applied. Alternatively the time-stamps can be used for creating a log of the events.

The Input Capture unit is illustrated by the block diagram shown in Figure 15-3. The elements of

the block diagram that are not directly a part of the Input Capture unit are gray shaded. The

small “n” in register and bit names indicates the Timer/Counter number.

Figure 15-3. Input Capture Unit Block Diagram

When a change of the logic level (an event) occurs on the Input Capture pin (ICP1), alternatively

on the Analog Comparator output (ACO), and this change confirms to the setting of the edge

detector, a capture will be triggered. When a capture is triggered, the 16-bit value of the counter

(TCNT1) is written to the Input Capture Register (ICR1). The Input Capture Flag (ICF1) is set at

the same system clock as the TCNT1 value is copied into ICR1 Register. If enabled (ICIE1 = 1),

the Input Capture Flag generates an Input Capture interrupt. The ICF1 Flag is automatically

cleared when the interrupt is executed. Alternatively the ICF1 Flag can be cleared by software

by writing a logical one to its I/O bit location.

Reading the 16-bit value in the Input Capture Register (ICR1) is done by first reading the low

byte (ICR1L) and then the high byte (ICR1H). When the low byte is read the high byte is copied

into the high byte temporary register (TEMP). When the CPU reads the ICR1H I/O location it will

access the TEMP Register.

The ICR1 Register can only be written when using a Waveform Generation mode that utilizes

the ICR1 Register for defining the counter’s TOP value. In these cases the Waveform Genera-

ICFn (Int.Req.)

Analog

Comparator

WRITE

ICRn (16-bit Register)

ICRnH (8-bit)

Noise

Canceler

ICPn

Edge

Detector

TEMP (8-bit)

DATA BUS (8-bit)

ICRnL (8-bit)

TCNTn (16-bit Counter)

TCNTnH (8-bit)

TCNTnL (8-bit)

ACIC*

ICNC

ICES

ACO*

ATmega169PV-8MCH 数据表(PDF) 113 Page - ATMEL Corporation

ATmega169PV-8MCH 数据表(HTML) 113 Page - ATMEL Corporation

Html Pages

1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 41 42 43 44 45 46 47 48 49 50 51 52 53 54 55 56 57 58 59 60 61 62 63 64 65 66 67 68 69 70 71 72 73 74 75 76 77 78 79 80 81 82 83 84 85 86 87 88 89 90 91 92 93 94 95 96 97 98 99 100 ...More

数据表下载