| 数据搜索系统,热门电子元器件搜索 |
|
ADM1029ARQZ-R7 数据表(PDF) 42 Page - ON Semiconductor |
|
|
|||||||||||||||||||||||||||||
ADM1029ARQZ-R7 数据表(HTML) 42 Page - ON Semiconductor |
|
42 / 50 page ![]() Rev. 1 | Page 42 of 50 | www.onsemi.com Register 09h – Set Fan x Full Speed (Power-On Default 00h) Bit Name R/W Description 0 Fan 1 Full Speed = 0 R/W When set to 1 Fan 1 will run at Full Speed. 1 Fan 2 Full Speed = 0 R/W When set to 1 Fan 2 will run at Full Speed. 2 Reserved R Unused. Will read back 0. 3 Reserved R Unused. Will read back 0. 4 Reserved R Unused. Will read back 0. 5 Reserved R Unused. Will read back 0. 6 Reserved R Unused. Will read back 0. 7 Reserved R Unused. Will read back 0. Register 0Ch – Fan Spin-Up Register (Power-On Default 03h) Bit Name R/W Description <7:4> Reserved R Unused 3 Spin-up Disable R/W When this bit is set to 1, fan spin-up to full speed will be disabled. <2:0> Fan Spin-up Time R/W These bits select the spin-up time for the fans 000 = 16 seconds 001 = 8 seconds 010 = 4 seconds 011 = 2 seconds (default) 100 = 1 second 101 = 0.25 seconds 110 = 1/16 second 111 = 1/64 second Register 10h, 11h – Fan x * Status (Power-On Default 0000 0?0?) Bit Name R/W Description 0 Missing = x R Reflects the state of Pins 4/21. Low means Fan x * is installed, High means it is missing. This bit will automatically return Low if a missing fan is replaced. 1 Missing _L = 0 R/W This bit is edge-triggered and latches a Fan x * missing event on removal of Fan x *. This bit is cleared by writing a 0 to it. 2 Fault_ = x R Inverse of Pin 2/23. Low on pin means Fan x * has a fault (Pins 2/23 Low), High on pin means it is OK. This bit will automatically return Low if Pin 2/23 goes high. 3 Fault_L_ = 0 R/W This bit is edge-triggered and latches a Fan x * fault event on Pin 2/23. This bit is cleared by writing a 0 to it. If the PRESENT pin for a fan input is high (fan not installed) this bit will be cleared automatically. 4 Sleep = 0 R/W When this bit is set, Fan x * will be stopped and no Fan x* faults will be monitored. If Bit 4 in Fan x * Fault Action Register is set then Fan x* will go to Alarm Speed if an overtemperature event is detected as per settings in the Temp Fault Action Registers. 5 Hot Plug Priority R/W This bit indicates whether Fan x * runs at Hot-Plug Speed (bit set to 1) or Alarm Speed (bit set to 0) if both modes are triggered. 6 Tach_Fault_L R/W Latches a Fan x * Tach fault. This bit is cleared by writing a 0 to it. If the PRESENT pin for a fan input is high (fan not installed) this bit will be cleared automatically. 7 Hot_Plug_L R/W This bit is edge-triggered and latches a Fan x * Hot-Plug event which is the insertion of Fan x *. (Note difference to Bit 1) This bit is cleared by writing a 0 to it. If a fan is Hot-Plug installed, it will run at Normal Speed. NOTES *“x” denotes the fan number. Register 10h is for Fan 1 and Register 11h is for Fan 2. Question marks on this and following pages indicate bit settings that depend on the state of certain pins on power-up. ADM1029 |
|
链接网址 |
| ALLDATASHEET是否为您带来帮助? [ DONATE ] |
关于 Alldatasheet | 广告服务 | 联系我们 | 隐私政策 | 数据表链接 | 链接交换 | 制造商名单 All Rights Reserved©Alldatasheet.com |
| Russian : Alldatasheetru.com | Korean : Alldatasheet.co.kr | Spanish : Alldatasheet.es | French : Alldatasheet.fr | Italian : Alldatasheetit.com Portuguese : Alldatasheetpt.com | Polish : Alldatasheet.pl | Vietnamese : Alldatasheet.vn Indian : Alldatasheet.in | Mexican : Alldatasheet.com.mx | British : Alldatasheet.co.uk | New Zealand : Alldatasheet.co.nz |
|
Family Site : ic2ic.com |
icmetro.com |