E2000 datasheet(67/104 Pages) INTEL

67 / 104 page

Land Listing and Signal Descriptions

Datasheet

DEFER#

Input

DEFER# is asserted by an agent to indicate that a transaction cannot

be ensured in-order completion. Assertion of DEFER# is normally

the responsibility of the addressed memory or input/output agent.

This signal must connect the appropriate pins/lands of all processor

FSB agents.

DRDY#

Input/

Output

DRDY# (Data Ready) is asserted by the data driver on each data

transfer, indicating valid data on the data bus. In a multi-common

clock data transfer, DRDY# may be de-asserted to insert idle clocks.

This signal must connect the appropriate pins/lands of all processor

FSB agents.

DSTBN[3:0]#

Input/

Output

DSTBN[3:0]# are the data strobes used to latch in D[63:0]#.

DSTBP[3:0]#

Input/

Output

DSTBP[3:0]# are the data strobes used to latch in D[63:0]#.

FCx

Other

FC signals are signals that are available for compatibility with other

processors.

FERR#/PBE#

Output

FERR#/PBE# (floating point error/pending break event) is a

multiplexed signal and its meaning is qualified by STPCLK#. When

STPCLK# is not asserted, FERR#/PBE# indicates a floating-point

error and will be asserted when the processor detects an unmasked

floating-point error. When STPCLK# is not asserted, FERR#/PBE# is

similar to the ERROR# signal on the Intel 387 coprocessor, and is

included for compatibility with systems using MS-DOS*-type

floating-point error reporting. When STPCLK# is asserted, an

assertion of FERR#/PBE# indicates that the processor has a pending

break event waiting for service. The assertion of FERR#/PBE#

indicates that the processor should be returned to the Normal state.

For additional information on the pending break event functionality,

including the identification of support of the feature and enable/

disable information, refer to volume 3 of the Intel Architecture

Software Developer's Manual and the Intel Processor Identification

and the CPUID Instruction application note.

GTLREF[1:0]

Input

GTLREF[1:0] determine the signal reference level for GTL+ input

signals. GTLREF is used by the GTL+ receivers to determine if a

signal is a logical 0 or logical 1.

Table 25.

Signal Description (Sheet 4 of 9)

Name

Type

Description

Signals

Associated Strobe

D[15:0]#, DBI0#

DSTBN0#

D[31:16]#, DBI1#

DSTBN1#

D[47:32]#, DBI2#

DSTBN2#

D[63:48]#, DBI3#

DSTBN3#

Signals

Associated Strobe

D[15:0]#, DBI0#

DSTBP0#

D[31:16]#, DBI1#

DSTBP1#

D[47:32]#, DBI2#

DSTBP2#

D[63:48]#, DBI3#

DSTBP3#

E2000 数据表(PDF) 67 Page - Intel Corporation

E2000 数据表(HTML) 67 Page - Intel Corporation

Html Pages

1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 41 42 43 44 45 46 47 48 49 50 51 52 53 54 55 56 57 58 59 60 61 62 63 64 65 66 67 68 69 70 71 72 73 74 75 76 77 78 79 80 81 82 83 84 85 86 87 88 89 90 91 92 93 94 95 96 97 98 99 100 ...More

数据表下载

链接网址

E2000 数据表(PDF) 67 Page - Intel Corporation

E2000 数据表(HTML) 67 Page - Intel Corporation

Html Pages

1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 41 42 43 44 45 46 47 48 49 50 51 52 53 54 55 56 57 58 59 60 61 62 63 64 65 66 67 68 69 70 71 72 73 74 75 76 77 78 79 80 81 82 83 84 85 86 87 88 89 90 91 92 93 94 95 96 97 98 99 100 ...More

数据表 下载

链接网址

数据表下载