E2000 datasheet(68/104 Pages) INTEL

68 / 104 page

Land Listing and Signal Descriptions

Datasheet

HIT#

HITM#

Input/

Output

Input/

Output

HIT# (Snoop Hit) and HITM# (Hit Modified) convey transaction

snoop operation results. Any FSB agent may assert both HIT# and

HITM# together to indicate that it requires a snoop stall, which can

be continued by reasserting HIT# and HITM# together.

IERR#

Output

IERR# (Internal Error) is asserted by a processor as the result of an

internal error. Assertion of IERR# is usually accompanied by a

SHUTDOWN transaction on the processor FSB. This transaction may

optionally be converted to an external error signal (e.g., NMI) by

system core logic. The processor will keep IERR# asserted until the

assertion of RESET#.

This signal does not have on-die termination. Refer to Section 2.6.2

for termination requirements.

IGNNE#

Input

IGNNE# (Ignore Numeric Error) is asserted to the processor to

ignore a numeric error and continue to execute noncontrol floating-

point instructions. If IGNNE# is de-asserted, the processor

generates an exception on a noncontrol floating-point instruction if a

previous floating-point instruction caused an error. IGNNE# has no

effect when the NE bit in control register 0 (CR0) is set.

IGNNE# is an asynchronous signal. However, to ensure recognition

of this signal following an Input/Output write instruction, it must be

valid along with the TRDY# assertion of the corresponding Input/

Output Write bus transaction.

INIT#

Input

INIT# (Initialization), when asserted, resets integer registers inside

the processor without affecting its internal caches or floating-point

registers. The processor then begins execution at the power-on

Reset vector configured during power-on configuration. The

processor continues to handle snoop requests during INIT#

assertion. INIT# is an asynchronous signal and must connect the

appropriate pins/lands of all processor FSB agents.

ITP_CLK[1:0]

Input

ITP_CLK[1:0] are copies of BCLK that are used only in processor

systems where no debug port is implemented on the system board.

ITP_CLK[1:0] are used as BCLK[1:0] references for a debug port

implemented on an interposer. If a debug port is implemented in the

system, ITP_CLK[1:0] are no connects in the system. These are not

processor signals.

LINT[1:0]

Input

LINT[1:0] (Local APIC Interrupt) must connect the appropriate pins/

lands of all APIC Bus agents. When the APIC is disabled, the LINT0

signal becomes INTR, a maskable interrupt request signal, and

LINT1 becomes NMI, a nonmaskable interrupt. INTR and NMI are

backward compatible with the signals of those names on the

Pentium processor. Both signals are asynchronous.

Both of these signals must be software configured via BIOS

programming of the APIC register space to be used either as NMI/

INTR or LINT[1:0]. Because the APIC is enabled by default after

Reset, operation of these signals as LINT[1:0] is the default

configuration.

Table 25.

Signal Description (Sheet 5 of 9)

Name

Type

Description

E2000 数据表(PDF) 68 Page - Intel Corporation

E2000 数据表(HTML) 68 Page - Intel Corporation

Html Pages

1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 41 42 43 44 45 46 47 48 49 50 51 52 53 54 55 56 57 58 59 60 61 62 63 64 65 66 67 68 69 70 71 72 73 74 75 76 77 78 79 80 81 82 83 84 85 86 87 88 89 90 91 92 93 94 95 96 97 98 99 100 ...More

数据表下载

链接网址

E2000 数据表(PDF) 68 Page - Intel Corporation

E2000 数据表(HTML) 68 Page - Intel Corporation

Html Pages

1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 41 42 43 44 45 46 47 48 49 50 51 52 53 54 55 56 57 58 59 60 61 62 63 64 65 66 67 68 69 70 71 72 73 74 75 76 77 78 79 80 81 82 83 84 85 86 87 88 89 90 91 92 93 94 95 96 97 98 99 100 ...More

数据表 下载

链接网址

数据表下载