| 数据搜索系统,热门电子元器件搜索 |
|
AD822 数据表(PDF) 25 Page - Analog Devices |
|
|
|||||||||||||||||||||||||||||
AD822 数据表(HTML) 25 Page - Analog Devices |
|
25 / 88 page ![]() ADuC841/ADuC842/ADuC843 Rev. 0 | Page 25 of 88 ADCCON2—(ADC Control SFR 2) The ADCCON2 register controls ADC channel selection and conversion modes as detailed below. SFR Address D8H SFR Power-On Default 00H Bit Addressable Yes Table 8. ADCCON2 SFR Bit Designations Bit No. Name Description 7 ADCI ADC Interrupt Bit. Set by hardware at the end of a single ADC conversion cycle or at the end of a DMA block conversion. Cleared by hardware when the PC vectors to the ADC interrupt service routine. Otherwise, the ADCI bit is cleared by user code. 6 DMA DMA Mode Enable Bit. Set by the user to enable a preconfigured ADC DMA mode operation. A more detailed description of this mode is given in the ADC DMA Mode section. The DMA bit is automatically set to 0 at the end of a DMA cycle. Setting this bit causes the ALE output to cease; it will start again when DMA is started and will operate correctly after DMA is complete. 5 CCONV Continuous Conversion Bit. Set by the user to initiate the ADC into a continuous mode of conversion. In this mode, the ADC starts converting based on the timing and channel configuration already set up in the ADCCON SFRs; the ADC automatically starts another conversion once a previous conversion has completed. 4 SCONV Single Conversion Bit. Set to initiate a single conversion cycle. The SCONV bit is automatically reset to 0 on completion of the single conversion cycle. 3 2 1 0 CS3 CS2 CS1 CS0 Channel Selection Bits. Allow the user to program the ADC channel selection under software control. When a conversion is initiated, the converted channel is the one pointed to by these channel selection bits. In DMA mode, the channel selection is derived from the channel ID written to the external memory. CS3 0 0 0 0 0 0 0 0 1 1 1 1 1 1 CS2 0 0 0 0 1 1 1 1 0 0 0 0 1 1 CS1 0 0 1 1 0 0 1 1 0 0 1 1 0 1 CS0 0 1 0 1 0 1 0 1 0 1 0 1 0 1 CH# 0 1 2 3 4 5 6 7 Temp Monitor DAC0 DAC1 AGND VREF DMA STOP Requires minimum of 1 µs to acquire. Only use with internal DAC output buffer on. Only use with internal DAC output buffer on. Place in XRAM location to finish DMA sequence; refer to the ADC DMA Mode section. All other combinations reserved. |
|
链接网址 |
| ALLDATASHEET是否为您带来帮助? [ DONATE ] |
关于 Alldatasheet | 广告服务 | 联系我们 | 隐私政策 | 数据表链接 | 链接交换 | 制造商名单 All Rights Reserved©Alldatasheet.com |
| Russian : Alldatasheetru.com | Korean : Alldatasheet.co.kr | Spanish : Alldatasheet.es | French : Alldatasheet.fr | Italian : Alldatasheetit.com Portuguese : Alldatasheetpt.com | Polish : Alldatasheet.pl | Vietnamese : Alldatasheet.vn Indian : Alldatasheet.in | Mexican : Alldatasheet.com.mx | British : Alldatasheet.co.uk | New Zealand : Alldatasheet.co.nz |
|
Family Site : ic2ic.com |
icmetro.com |