MEC1322 datasheet(79/456 Pages) MICROCHIP

79 / 456 page

 2014 - 2015 Microchip Technology Inc.

DS00001719D-page 79

MEC1322

The LPC Controller claims only LPC transactions targeted for one of its peripherals. Section 5.8.2, on page 81,

describes the mechanism for Claiming and Forwarding Transactions for Supported LPC Cycles. LPC transactions may

be used to configure the chip and to access registers during operation. The mechanism to configure the chip is

described in Section 5.8.3, "Configuration Port," on page 83.

LPC memory cycles may also be used to access the Base Address Registers of certain devices.

Once configured, the LPC peripherals implemented as logical devices on chip may use the SERIRQ to notify the host

of an event. See Section 5.8.4, "Serial IRQs," on page 84.

5.8.1

LPC CONTROLLER DESCRIPTION

The following sections qualify the LPC features implemented according to the LPC Specification.

5.8.1.1

Cycle Types Supported

The following cycle types are supported by the LPC Interface Controller. All other cycles that it does not support are

ignored.

When the LPC Controller detects a transaction targeted for this device it claims and forwards that transaction as defined

in Section 5.8.2, "Claiming and Forwarding Transactions for Supported LPC Cycles," on page 81.

LPC I/O CYCLES

The system host may use LPC I/O cycles to read/write the I/O mapped configuration and runtime registers implemented

in this device. See the Intel® Low Pin Count (LPC) Interface Specification, v1.1, Section 5.2 for definition of LPC I/O

Cycles.

LPC MEMORY CYCLES

The system host may use LPC memory cycles to access memory mapped registers implemented in this device. See

the Intel® Low Pin Count (LPC) Interface Specification, v1.1, Section 5.1 for definition of LPC Memory Cycles.

5.8.1.2

LAD[3:0] Fields

The LAD[3:0] signals support multiple fields for each protocol as defined in section 4.2.1 LAD[3:0] of the Intel® Low Pin

Count (LPC) Interface Specification, v1.1. The following sections further qualify the fields supported.

WAIT SYNCS ON LPC

LPC transactions that access registers located on the device require a minimum of two wait SYNCs on the LPC bus.

The number of SYNCs may be larger if the internal bus is in use by the embedded controller, of if the data referenced

by the host is not present in a register. The device always uses Long Wait SYNCs, rather than Short Wait SYNCs, when

responding to an LPC bus request.

ERROR SYNCS ON LPC

The device does not issue ERROR SYNC cycles.

TABLE 5-8:

LPC CYCLE TYPES SUPPORTED

Cycle Type

Transfer Size

I/O Read

1 byte

I/O Write

1 byte

Memory Read

1 byte

Memory Write

1 byte

Note:

All LPC transactions are synchronized to the LCLK and will complete with a maximum of 8 wait states,

unless otherwise noted.

MEC1322 数据表(PDF) 79 Page - Microchip Technology

MEC1322 数据表(HTML) 79 Page - Microchip Technology

Html Pages

1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 41 42 43 44 45 46 47 48 49 50 51 52 53 54 55 56 57 58 59 60 61 62 63 64 65 66 67 68 69 70 71 72 73 74 75 76 77 78 79 80 81 82 83 84 85 86 87 88 89 90 91 92 93 94 95 96 97 98 99 100 ...More

数据表下载

链接网址

MEC1322 数据表(PDF) 79 Page - Microchip Technology

MEC1322 数据表(HTML) 79 Page - Microchip Technology

Html Pages

1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 41 42 43 44 45 46 47 48 49 50 51 52 53 54 55 56 57 58 59 60 61 62 63 64 65 66 67 68 69 70 71 72 73 74 75 76 77 78 79 80 81 82 83 84 85 86 87 88 89 90 91 92 93 94 95 96 97 98 99 100 ...More

数据表 下载

链接网址

数据表下载