TVP7002IPZP datasheet(12/58 Pages) TI1

12 / 58 page

TVP7002

SLES206C – MAY 2007 – REVISED APRIL 2013

www.ti.com

The selection between bottom- and mid-level clamping is performed by I2C subaddress 10h (see Sync-On-Green

Threshold). The fine clamps must also be enabled via I2C register 2Ah for proper operation. The internal

clamping time can be adjusted using the I2C clamp start and width registers at subaddress 05h and 06h,

respectively (see Clamp Start and Clamp Width).

Table 3. Recommended Clamp Setting by Video Mode

SOG INPUT

GREEN ADC CHANNEL

RED ADC CHANNEL

BLUE ADC CHANNEL

VIDEO MODE

(Y/G)

(Pr/R)

(Pb/B)

YPbPr component

Coarse

Fine Bottom Level

Fine Mid Level

PC graphics

Coarse

Fine Bottom Level

SCART-RGB

Coarse

Fine Bottom Level

A single-pole low-pass filter with three selectable cutoff frequencies (0.5, 1.7, and 4.8 MHz) is implemented in the

feedback loop of the sync-tip clamp circuit.

Programmable Gain Control

The TVP7002 provides a 4-bit coarse analog gain control (before A/D conversion) and an 8-bit fine digital gain

control (after A/D conversion). The coarse analog gain and the fine digital gain are both independently

programmable for each ADC channel.

Coarse Gain Control

The 4-bit coarse analog gain control has a 4:1 linear gain control range defined by the following equation.

Coarse Gain = 0.5 + NCG/10, where 0 ≤ NCG ≤ 15

0.5

≤ Coarse Gain ≤ 2.0

Default: NCG = 7 (Coarse Gain = 1.2)

The 4-bit coarse gain control can scale a signal with a voltage-input compliance of 0.5 VP-P to 2 VP-P to a full-

scale 10-bit A/D output code range. The minimum gain corresponds to a code 0h (2-VP-P full-scale input, –6-dB

gain) while the maximum gain corresponds to code Fh (0.5-VP-P full scale, +6 dB gain). The 4-bit coarse gain

control is independently controllable for each ADC channel (Red Coarse Gain, Green Coarse Gain, and Blue

Coarse Gain).

Fine Gain Control

The 8-bit fine digital gain control has a 2:1 linear gain control range defined by the following equation.

Fine Gain = 1.0 + NFG/256 where 0 ≤ NFG ≤ 255

1.0

≤ Fine Gain < 2.0

Default: NFG = 0 (Fine Gain = 1.0)

The 8-bit fine gain control is independently controllable for each ADC channel (Red Fine Gain, Green Fine Gain,

and Blue Fine Gain). For a normal PC graphics input, the fine gain is used mostly.

Programmable Offset Control

The TVP7002 provides a 6-bit coarse analog offset control (before A/D conversion) and a 10-bit fine digital offset

control (after A/D conversion). The coarse analog offset and the fine digital offset are both independently

programmable for each ADC channel.

Coarse Offset Control

A 6-bit code sets the coarse offset (Red Coarse Offset, Green Coarse Offset, Blue Coarse Offset) with individual

adjustment per channel. The coarse offset ranges from –32 counts to +31 counts. The coarse offset registers

apply before the ADC.

Fine Offset Control

A 10-bit fine offset registers (Red Fine Offset, Green Fine Offset, Blue Fine Offset) apply after the ADC. The fine

offset ranges from –512 counts to +511 counts.

Submit Documentation Feedback

Product Folder Links: TVP7002

TVP7002IPZP 数据表(PDF) 12 Page - Texas Instruments

TVP7002IPZP 数据表(HTML) 12 Page - Texas Instruments

Html Pages

1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 41 42 43 44 45 46 47 48 49 50 51 52 53 54 55 56 57 58

数据表下载

链接网址

TVP7002IPZP 数据表(PDF) 12 Page - Texas Instruments

TVP7002IPZP 数据表(HTML) 12 Page - Texas Instruments

Html Pages

1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 41 42 43 44 45 46 47 48 49 50 51 52 53 54 55 56 57 58

数据表 下载

链接网址

数据表下载