 |
数据搜索系统，热门电子元器件搜索 |
|
|
数据搜索系统，热门电子元器件搜索 |
|
ST6380 数据表(PDF) 25 Page - STMicroelectronics |
|
|
|||||||||||||||||||||||||||||
ST6380 数据表(HTML) 25 Page - STMicroelectronics |
|
|
25 / 82 page  25/82 ST6380, ST6381, ST6382, ST6383, ST6388, ST6389 INTERRUPTS (Cont’d) 3.5.3 Interrupt Option Register Interrupt Option Register (IOR) Address: (C8h) - Write only Reset Value: X000XXXXb The Interrupt Option Register (IOR register, loca- tion C8h) is used to enable/disable the individual in- terrupt sources and to select the operating mode of the external interrupt inputs. This register can be ad- dressed in the Data Space as RAM location at the C8h address, nevertheless it is a write-only register that can not be accessed with single-bit operations. The operating modes of the external interrupt inputs associated to interrupt vectors #1 and #2 are se- lected through bits 5 and 6 of the IOR register. Caution: This register contains at least one write only bit. Single bit instructions (SET, RES, INC and DEC) should not be used. D7. Not used. EL1. This is the Edge/Level selection bit of inter- rupt #1. When set to one, the interrupt is generat- ed on low level of the related signal; when cleared to zero, the interrupt is generated on falling edge. The bit is cleared to zero after reset. ES2. This is the edge selection bit on interrupt #2. This bit is used on the ST638x devices with on- chip OSD generator for VSYNC detection. When this bit is se to one, the interrupt #2 is positive edge sensitive, when cleared to zero the negative edge sensitive interrupt is selected. GEN. This is the global enable bit. When set to one all interrupts are globally enabled; when this bit is cleared to zero all interrupts are disabled (ex- cluding NMI). D3 - D0. These bits are not used. 3.5.4 Interrupt Procedure The interrupt procedure is very similar to a call pro- cedure; the user can consider the interrupt as an asynchronous call procedure. As this is an asyn- chronous event the user does not know about the context and the time at which it occurred. As a result the user should save all the data space registers which will be used inside the interrupt routines. There are separate sets of processor flags for nor- mal, interrupt and non-maskable interrupt modes which are automatically switched and so these do not need to be saved. The following list summarizes the interrupt proce- dure (refer also to Figure 19*) – Interrupt detection – The flags C and Z of the main routine are ex- changed with the flags C and Z of the interrupt routine (resp. the NMI flags) – The value of the PC is stored in the first level of the stack - The normal interrupt lines are inhibit- ed (NMI still active) – The edge flip-flop is reset – The related interrupt vector is loaded in the PC. – User selected registers are saved inside the in- terrupt service routine (normally on a software stack) – The source of the interrupt is found by polling (if more than one source is associated to the same vector) – Interrupt servicing – Return from interrupt (RETI) – Automatically the ST638x core switches back to the normal flags (resp the interrupt flags) and pops the previous PC value from the stack Figure 19. Interrupt Processing Flow-Chart 70 - EL1 ES2 GEN -- -- INSTRUCTION FETCH INSTRUCTION EXECUTE INSTRUCTION WAS THE INSTRUCTION A RETI ? ? CLEAR INTERRUPT MASK SELECT PROGRAM FLAGS “POP” THE STACKED PC ? CHECK IF THERE IS AN INTERRUPT REQUEST AND INTERRUPT MASK SELECT INTERNAL MODE FLAG PUSH THE PC INTO THE STACK LOAD PC FROM INTERRUPT VECTOR (FFC/FFD) SET INTERRUPT MASK NO NO YES IS THE CORE ALREADY IN NORMAL MODE? VA000014 YES NO YES |
|
链接网址 |
| ALLDATASHEET是否为您带来帮助? [ DONATE ] |
关于 Alldatasheet | 广告服务 | 联系我们 | 隐私政策 | 数据表链接 | 链接交换 | 制造商名单 All Rights Reserved©Alldatasheet.com |
| Russian : Alldatasheetru.com | Korean : Alldatasheet.co.kr | Spanish : Alldatasheet.es | French : Alldatasheet.fr | Italian : Alldatasheetit.com Portuguese : Alldatasheetpt.com | Polish : Alldatasheet.pl | Vietnamese : Alldatasheet.vn Indian : Alldatasheet.in | Mexican : Alldatasheet.com.mx | British : Alldatasheet.co.uk | New Zealand : Alldatasheet.co.nz |
|
Family Site : ic2ic.com |
icmetro.com |
Chinese ▼
English
Chinese
German
Japanese
Russian
Korean
Spanish
French
Italian
Portuguese
Polish
Vietnamese
Indian
Mexican
British
New Zealand
