ST6380 datasheet(51/82 Pages) STMICROELECTRONICS

51 / 82 page

51/82

ST6380, ST6381, ST6382, ST6383, ST6388, ST6389

ON-SCREEN DISPLAY (Cont’d)

Display Character Register (Ch)

See Data RAM Table Description for Specific Ad-

dress —

Read/Write

C7-C6. This bits must be different from “11”.

C7-C0. Character code. The 8 bits character code

(range: 00h to 0BFh) selects the character from a

set of 192 characters available.

Space Character Format Register (Ch)

See Data RAM Table Description for Specific Ad-

dress —

Read/Write

D7-D6. This bits must be “11”.

R, G, B. Colour. The 3 colour control bits define

the foreground colour of the following word as

shown in table below.

Table 17. Space Character Register Colour

Setting.

BGS. Background Select. The background select

bit selects the desired background for the following

word. There are two possible backgrounds defined

by the bits in the Background Control Register.

“0” The background on the following word is ena-

bled by BG0 and the colour is set by R0, G0,

and B0.

“1” The background on the following word is ena-

bled by BG1 and the colour is set by R1, G1,

and B1.

WE. Word Enable. The word enable bit defines

whether or not the following word is displayed.

“0” The word is not displayed.

“1” If the global enable bit and the OSD ram ena-

ble bit are set, then the word is displayed.

HSE. Horizontal Space Enable. The horizontal

space enable bit determines the spacing between

words.

“0” The space between words is equal to the width

of the space character, which is 14 dots.

“1” The space between words is defined by the

value in the horizontal space register plus the

width of the space character.

Character Set

The character set is user defined as ROM mask

option.

The OSD contains eight registers and 168 RAM lo-

cations. The eight registers are the Vertical Start

Address register, Horizontal Start Address regis-

ter, Vertical Space registers (VSR0 and VSR1),

Horizontal Space register, Background Control

Polarity Select register can be written at any time

by the ST6 Core. The access to the next five reg-

isters and the RAM is controlled through the state

of the Global Enable register.

The first six registers and the RAM are located in

page 5 of the paged memory of the ST6388 MCU.

This page contains 64 memory locations. This

paged memory is mapped into the memory loca-

tions 00h to 3Fh of the ST6388 memory map. A

page of memory is enabled by setting the desired

page bit, located in the Data Ram Bank Register,

to a one. The page register is at location E8h. The

hexadecimal value 20h selects page 5 - the OSD

RAM and registers (except PSR). As the OSD

RAM consists of 168 words, this RAM is further

paged using two bits (LS1/LS0) in the Global Ena-

ble register, in order to fit onto the 64 locations of

the page 5 of the MCU RAM space. Table 18

shows the addresses of the OSD registers and

RAM.

BGS

HSE

Colour

Black

Blue

Green

Cyan

Red

Magenta

Yellow

White

ST6380 数据表(PDF) 51 Page - STMicroelectronics

ST6380 数据表(HTML) 51 Page - STMicroelectronics

Html Pages

1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 41 42 43 44 45 46 47 48 49 50 51 52 53 54 55 56 57 58 59 60 61 62 63 64 65 66 67 68 69 70 71 72 73 74 75 76 77 78 79 80 81 82

数据表下载