ADE7763ARS datasheet(23/56 Pages) AD

23 / 56 page

ADE7763

Rev. A | Page 23 of 56

ADC 2

ANALOG

INPUT RANGE

0.5V, 0.25V, 0.125V,

62.5mV, 31.25mV

REFERENCE

LPF1

ACTIVE AND REACTIVE

ENERGY CALCULATION

VRMS CALCULATION

AND WAVEFORM

SAMPLING

(PEAK/SAG/ZX)

PGA2

×1, ×2, ×4,

×8, ×16

{GAIN[7:5]}

V2P

V2N

2.42V

0x2852

0x2581

0xDAE8

0xD7AE

0x0000

LPF OUTPUT

WORD RANGE

Figure 47. ADC and Signal Processing in Channel 2

VRMS[23:0]

LPF3

LPF1

CHANNEL 2

0x17D338

0x00

VRMOS[11:0]

VOLTAGE SIGNAL (V(t))

sgn

22 21 20

0x2518

0x0

0xDAE8

Figure 48. Channel 2 RMS Signal Processing

Channel 2 has only one analog input range (0.5 V differential).

Like Channel 1, Channel 2 has a PGA with gain selections of 1,

2, 4, 8, and 16. For energy measurement, the output of the ADC

is passed directly to the multiplier and is not filtered. An HPF is

not required to remove any dc offset; it is only required that the

offset is removed from one channel to eliminate errors caused

by offsets in the power calculation. In waveform sampling mode,

one of four output sample rates can be chosen by using Bits 11

and 12 of the mode register. The available output sample rates

are 27.9 kSPS, 14 kSPS, 7 kSPS, or 3.5 kSPS—see the Mode

indicates that a sample is available by going active low. The

timing is the same as that for Channel 1, as shown in Figure 44.

Channel 2 RMS Calculation

Figure 48 shows the details of the signal processing chain for the

rms calculation on Channel 2. The Channel 2 rms value is

processed from the samples used in the Channel 2 waveform

sampling mode. The rms value is slightly attenuated due to

LPF1. The Channel 2 rms value is stored in the unsigned, 24-bit

VRMS register. The update rate of the Channel 2 rms

measurement is CLKIN/4.

With the specified full-scale ac analog input signal of 0.5 V, the

output from LPF1 swings between 0x2518 and 0xDAE8 at

60 Hz—see the Channel 2 ADC section. The equivalent rms

value of this full-scale ac signal is approximately 1,561,400

(0x17 D338) in the VRMS register. The voltage rms measure-

ment provided in the ADE7763 is accurate to within ±0.5% for

signal input between full scale and full scale/20. The conversion

from the register value to volts must be done externally in the

microprocessor using a volts/LSB constant. Because the low-pass

filter used for calculating the rms value is imperfect, there is some

ripple noise from 2ω term present in the rms measurement. To

minimize the effect of noise in the reading, synchronize the rms

reading with the zero crossings of the voltage input.

Channel 2 RMS Offset Compensation

The ADE7763 incorporates a Channel 2 rms offset

compensation register (VRMSOS). This is a 12-bit, signed

calculation. An offset could exist in the rms calculation due to

input noises and dc offset in the input samples. The offset

calibration allows the contents of the VRMS register to be

maintained at 0 when no voltage is applied. One LSB of the

Channel 2 rms offset is equivalent to 1 LSB of the rms register.

Assuming that the maximum value of the Channel 2 rms

calculation is 1,561,400d with full-scale ac inputs, then 1 LSB of

the Channel 2 rms offset represents 0.064% of measurement

error at –60 dB down of full scale.

VRMS = VRMS0 + VRMSOS

(6)

where

VRMS0 is the rms measurement without offset

correction.

The voltage rms offset compensation should be done by testing

the rms results at two nonzero input levels. One measurement

can be done close to full scale and the other at approximately

full scale/10. The voltage offset compensation can be derived

from these measurements. If the voltage rms offset register does

not have enough range, the CH2OS register can also be used.

ADE7763ARS 数据表(PDF) 23 Page - Analog Devices

ADE7763ARS 数据表(HTML) 23 Page - Analog Devices

Html Pages

1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 41 42 43 44 45 46 47 48 49 50 51 52 53 54 55 56

数据表下载