ADE1202 datasheet(20/42 Pages) AD

20 / 42 page

ADE1202

Data Sheet

Rev. 0 | Page 20 of 42

COMPARATOR

OUTPUT

DEBOUNCE

FILTER

COUNTER

DEBOUNCE FILTER

OUTPUT

DEBOUNCE FILTER

COUNTER

UP/DOWN MODE

UP/CLEAR MODE

DEBOUNCE FILTER

OUTPUT

TIME

FILTER LENGTH

TIME

Figure 32. Debounce Filter Function Example

INVALID MODE

The register protection feature must be disabled when

configuring the ADE1202 (see the Protecting the Integrity of

Configuration Registers section). During this time, the state of

the DOUT1 pin and DOUT2 pin does not reflect the state of

the inputs on the IN1 pin and IN2 pin, and the IC is in invalid

mode. The IC remains in this mode until the register protection

is enabled.

During invalid mode, the ADE1202 output on the DOUT1 pin

and DOUT2 pin is set based on Bits[5:4] (INVALID_MODE)

and Bit 3 (FORCEVAL) of the BIN_CTRL register.

If the INVALID_MODE bits are equal to 00, the DOUT1 and

DOUT2 filter outputs are set to the value configured in the

FORCEVAL bit in the BIN_CTRL register. If the bits are equal

to 01, the DOUT1 and DOUT2 filter outputs are set to the

DOUTx output from the digital datapath. If the bits are equal to

10, the DOUT1 and DOUT2 filter outputs toggle the value they

had upon entering invalid mode. If the bits are equal to 11, the

DOUT1 and DOUT2 filter outputs hold the current value.

PROGRAMMABLE LOAD CURRENT

The ADE1202 programmable load current block diagram is

shown in Figure 33. The input impedance of the programmable

load is given in Table 1. When the programmable load is disabled

with the PL_EN register, Bit 15 and Bit 14 = 00, and the external

FET is conducting, the load sinks ~100 µA.

ADE1202

56kΩ

LOADx

GNDF

Figure 33. Programmable Load Current Block Diagram

A high voltage digital input is presented to the ADE1202

application circuit, as shown in Figure 23. When the digital

input switches on to a high voltage state, the ADE1202 injects a

pulsed current load for a user defined period of time based on

the PL_HIGH_TIME register, and then switches to a constant

current. The pulsed current is sometimes called a wetting current

and removes oxidation from the digital input contacts, as well as

minimizes the effects of surge and electrical fast transients.

To calculate the value to write to the HIGH_CODE bits

(Bits[7:0]) of the PL_HIGH_CODE register to configure the

pulsed current, use the following equation:

HIGH_CODE = Pulsed Current/0.2

(2)

where Pulsed Current is the desired current level expressed in

mA. The resolution of the pulsed current is 0.2 mA per LSB.

The maximum current is (28 − 1) × 0.2 = 51 mA.

The recommended range of the pulsed current is between 20 mA

and 50 mA, and HIGH_CODE = 100 decimal to 250 decimal.

The minimum current is 0.2 mA and HIGH_CODE = 1.

The pulsed current is applied for a time period set in Bits[11:0]

(HIGH_TIME) in the PL_HIGH_TIME register.

To determine the value to write to the HIGH_TIME bit field

based on the desired period of the pulse, use the following

equation:

HIGH_TIME = Pulsed Current Period/10

(3)

where Pulsed Current Period is the desired time period

expressed in µs. The resolution of the pulsed current period is

10 µs. The maximum period is (212 − 1) × 10 (µs) = 40.95 ms.

After the pulsed current period, the programmable load

switches to a constant current level set in the LOW_CODE bits

(PL_LOW_CODE register, Bits[5:0]). To determine the value to

write to the LOW_CODE bit field, use the following equation:

LOW_CODE = Constant Current/0.1

(4)

where:

Constant Current is the desired current level expressed in mA.

The resolution of the constant current is 0.1 mA per LSB.

The maximum current that can be set is (26 − 1) × 0.1 = 6.3 mA.

ADE1202 数据表(PDF) 20 Page - Analog Devices

ADE1202 数据表(HTML) 20 Page - Analog Devices

Html Pages

1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 41 42

数据表下载

链接网址

ADE1202 数据表(PDF) 20 Page - Analog Devices

ADE1202 数据表(HTML) 20 Page - Analog Devices

Html Pages

1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 41 42

数据表 下载

链接网址

数据表下载