M58PR512LE datasheet(47/119 Pages) STMICROELECTRONICS

47 / 119 page

M58PR256LE, M58PR512LE, M58PR001LE

Status Register

47/119

6.2

Object program mode status bit (SR8)

The object program mode status bit, SR8, indicates whether an error occurred while writing

to a program region that was configured in the object program mode.

The SR8 bit should be read once the Program/Erase Controller status bit SR7 is set to ‘1’

(Program/Erase Controller inactive).

SR8 is set to 1 when the user attempts to rewrite an object mode region.

When:

●

SR8 = 0, the program operation completed successfully.

●

SR8 = 1, the program operation failed.

Once set, SR8 can only be cleared by issuing a Clear Status Register command or through

a hardware reset.

SR8 should be cleared before a new program command is issued, otherwise the new

command appears to fail.

6.3

Program/Erase Controller status bit (SR7)

The Program/Erase Controller status bit indicates whether the Program/Erase Controller is

active or inactive in any bank.

When:

●

SR7 = 0, the Program/Erase Controller is active.

●

SR7 = 1, the Program/Erase Controller is inactive, and the device is ready to process a

new command.

The Program/Erase Controller status bit is set to ’0’ immediately after a Program/Erase

Suspend command is issued until the Program/Erase Controller pauses. After the

Program/Erase Controller pauses, the bit is set to ’1’.

6.4

Erase suspend status bit (SR6)

The erase suspend status bit indicates that an erase operation has been suspended in the

addressed block.

When:

●

SR6 = 0, no Program/Erase Suspend command has been issued.

●

SR6 = 1, a Program/Erase Suspend command has been issued and the memory is

waiting for a Program/Erase Resume command.

The erase suspend status bit should only be considered valid when the Program/Erase

Controller status bit is set to ’1’ (Program/Erase Controller inactive). SR6 is set within the

erase suspend latency time of the Program/Erase Suspend command being issued,

therefore, the memory may still complete the operation rather than entering suspend mode.

When a Program/Erase Resume command is issued, the erase suspend status bit is reset

to ’0’.

M58PR512LE 数据表(PDF) 47 Page - STMicroelectronics

M58PR512LE 数据表(HTML) 47 Page - STMicroelectronics

Html Pages

1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 41 42 43 44 45 46 47 48 49 50 51 52 53 54 55 56 57 58 59 60 61 62 63 64 65 66 67 68 69 70 71 72 73 74 75 76 77 78 79 80 81 82 83 84 85 86 87 88 89 90 91 92 93 94 95 96 97 98 99 100 ...More

数据表下载

链接网址

M58PR512LE 数据表(PDF) 47 Page - STMicroelectronics

M58PR512LE 数据表(HTML) 47 Page - STMicroelectronics

Html Pages

1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 41 42 43 44 45 46 47 48 49 50 51 52 53 54 55 56 57 58 59 60 61 62 63 64 65 66 67 68 69 70 71 72 73 74 75 76 77 78 79 80 81 82 83 84 85 86 87 88 89 90 91 92 93 94 95 96 97 98 99 100 ...More

数据表 下载

链接网址

数据表下载