M58PR512LE datasheet(48/119 Pages) STMICROELECTRONICS

48 / 119 page

Status Register

M58PR256LE, M58PR512LE, M58PR001LE

48/119

6.5

Erase status bit (SR5)

The erase status bit identifies if there is an error during a block erase operation.

When:

●

SR5 = 0, no error occurred.

●

SR5 = 1, the Program/Erase Controller applied the maximum number of pulses to the

block or bank and still failed to verify that it has erased correctly.

The erase status bit should be read once the Program/Erase Controller Status bit is set to ’1’

(Program/Erase Controller inactive). Once set, the erase status bit must be cleared by a

Clear Status Register command or a hardware reset. This must be done before a new erase

command is issued, otherwise the new command appears to fail.

6.6

Program status bit (SR4)

The program status bit identifies if there is an error during a program operation.

The program status bit should be read once the Program/Erase Controller status bit is set to

‘1’ (Program/Erase Controller inactive).

When:

●

SR4 = 0, no error occurred.

●

SR4 = 1, the Program/Erase Controller applied the maximum number of pulses to the

word and still failed to verify that it programmed correctly.

Attempting to program a '1' to an already programmed bit while VPP = VPPH also sets the

program status bit to ’1’. If VPP is different from VPPH, SR4 remains set to '0' and the attempt

is not shown.

Once set to '1', the program status bit must be cleared by a Clear Status Register command

or a hardware reset. This must be done before a new program command is issued,

otherwise the new command appears to fail.

6.7

VPP status bit (SR3)

The VPP status bit identifies an invalid voltage on the VPP pin during program and erase

operations. The VPP pin is only sampled at the beginning of a program or erase operation.

Program and erase operations are not guaranteed if VPP becomes invalid during an

operation.

When:

●

SR3 = 0, the voltage on the VPP pin is sampled at a valid voltage.

●

SR3 = 1, the VPP pin has a voltage that is below the VPP lockout voltage, VPPLK, the

memory is protected, and program and erase operations cannot be performed.

Once set to ‘1’, the VPP status bit must be cleared by a Clear Status Register command or a

hardware reset. This must be done before a new program or erase command is issued,

otherwise the new command appears to fail.

M58PR512LE 数据表(PDF) 48 Page - STMicroelectronics

M58PR512LE 数据表(HTML) 48 Page - STMicroelectronics

Html Pages

1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 41 42 43 44 45 46 47 48 49 50 51 52 53 54 55 56 57 58 59 60 61 62 63 64 65 66 67 68 69 70 71 72 73 74 75 76 77 78 79 80 81 82 83 84 85 86 87 88 89 90 91 92 93 94 95 96 97 98 99 100 ...More

数据表下载

链接网址

M58PR512LE 数据表(PDF) 48 Page - STMicroelectronics

M58PR512LE 数据表(HTML) 48 Page - STMicroelectronics

Html Pages

1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 41 42 43 44 45 46 47 48 49 50 51 52 53 54 55 56 57 58 59 60 61 62 63 64 65 66 67 68 69 70 71 72 73 74 75 76 77 78 79 80 81 82 83 84 85 86 87 88 89 90 91 92 93 94 95 96 97 98 99 100 ...More

数据表 下载

链接网址

数据表下载