ADE7166 datasheet(124/144 Pages) AD

124 / 144 page

ADE7566/ADE7569/ADE7166/ADE7169

Rev. A | Page 124 of 144

All of the following conditions must be met at the time the final

shift pulse is generated to receive a character:

UART OPERATION MODES

Mode 0 (Shift Register with Baud Rate Fixed at fCORE/12)

•

If the extended UART is disabled (EXTEN = 0 in the CFG

SFR), RI must be 0 to receive a character. This ensures that

the data in the SBUF SFR is not overwritten if the last

received character has not been read.

Mode 0 is selected when the SM0 and SM1 bits in the Serial

Communications Control Register Bit Description SFR (SCON,

0x98) are cleared. In this shift register mode, serial data enters

and exits through RxD. TxD outputs the shift clock. The baud

rate is fixed at fCORE/12. Eight data bits are transmitted or

received.

•

If frame error checking is enabled by setting SM2, the

received stop bit must be set to receive a character. This

ensures that every character received comes from a valid

frame, with both a start bit and a stop bit.

Transmission is initiated by any instruction that writes to the

Serial Port Buffer SFR (SBUF, 0x99). The data is shifted out of

the RxD line. The eight bits are transmitted with the least

significant bit (LSB) first.

If any of these conditions are not met, the received frame is

irretrievably lost, and the receive interrupt flag (RI) is not set.

Reception is initiated when the receive enable bit (REN) is 1

and the receive interrupt bit (RI) is 0. When RI is cleared, the

data is clocked into the RxD line, and the clock pulses are

output from the TxD line as shown in

If the received frame has met the previous criteria, the following

events occur:

•

The eight bits in the receive shift register are latched into

the SBUF SFR.

Figure 102.

RxD

(DATA OUT)

TxD

(SHIFT CLOCK)

DATA BIT 0

DATA BIT 1

DATA BIT 6

DATA BIT 7

•

The ninth bit (stop bit) is clocked into RB8 in the SCON SFR.

•

The receiver interrupt flag (RI) is set.

Mode 2 (9-Bit UART with Baud Fixed at fCORE/64 or fCORE/32)

Figure 102. 8-Bit Shift Register Mode

Mode 2 is selected by setting SM0 and clearing SM1. In this

mode, the UART operates in 9-bit mode with a fixed baud rate.

The baud rate is fixed at fCORE/64 by default, although setting the

SMOD bit in the Program Control SFR (PCON, 0x87) doubles

the frequency to fCORE/32. Eleven bits are transmitted or received:

a start bit (0), eight data bits, a programmable ninth bit, and a

stop bit (1). The ninth bit is most often used as a parity bit or as

part of a multiprocessor communication protocol, although it

can be used for anything, including a ninth data bit, if required.

Mode 1 (8-Bit UART, Variable Baud Rate)

Mode 1 is selected by clearing SM0 and setting SM1. Each data

byte (LSB first) is preceded by a start bit (0) and followed by a

stop bit (1). Therefore, each frame consists of 10 bits transmitted

on TxD or received on RxD.

The baud rate is set by a timer overflow rate. Timer 1 or Timer 2

can be used to generate baud rates, or both timers can be used

simultaneously where one generates the transmit rate and the

other generates the receive rate. There is also a dedicated timer

for baud rate generation, the UART timer, which has a fractional

divisor to precisely generate any baud rate (see the

To use the ninth data bit as part of a communication protocol for

a multiprocessor network such as RS-485, the ninth bit is set to

indicate that the frame contains the address of the device with

which the master wants to communicate. The devices on the

network are always listening for a packet with the ninth bit set

and are configured such that if the ninth bit is cleared, the frame

is not valid, and a receive interrupt is not generated. If the ninth

bit is set, all devices on the network receive the address and obtain a

receive character interrupt. The devices examine the address and, if

it matches one of the device’s preprogrammed addresses, that

device configures itself to listen to all incoming frames, even those

with the ninth bit cleared. Because the master has initiated

communication with that device, all the following packets with

the ninth bit cleared are intended specifically for that addressed

device until another packet with the ninth bit set is received. If

the address does not match, the device continues to listen for

address packets.

UART Timer

Generated Baud Rates section).

Transmission is initiated by a write to the Serial Port Buffer SFR

(SBUF, 0x99). Next, a stop bit (1) is loaded into the ninth bit

position of the transmit shift register. The data is output bit-by-

bit until the stop bit appears on TxD and the transmit interrupt

flag (TI) is automatically set as shown in Figure 103.

TxD

(SCON.1)

START

BIT

STOP BIT

SET INTERRUPT

(FOR EXAMPLE,

READY FOR MORE DATA)

Figure 103. 8-Bit Variable Baud Rate

Reception is initiated when a 1-to-0 transition is detected on

RxD. Assuming that a valid start bit is detected, character

reception continues. The eight data bits are clocked into the

serial port shift register.

ADE7166 数据表(PDF) 124 Page - Analog Devices

ADE7166 数据表(HTML) 124 Page - Analog Devices

Html Pages

1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 41 42 43 44 45 46 47 48 49 50 51 52 53 54 55 56 57 58 59 60 61 62 63 64 65 66 67 68 69 70 71 72 73 74 75 76 77 78 79 80 81 82 83 84 85 86 87 88 89 90 91 92 93 94 95 96 97 98 99 100 ...More

数据表下载