PC48F4400PLVB0 datasheet(56/102 Pages) NUMONYX

56 / 102 page

Numonyx™ Wireless Flash Memory (W18)

Datasheet

November 2007

Order Number: 290701-18

Numonyx™ Wireless Flash Memory (W18)

output on valid CLK edges following a minimum delay. However, for a synchronous non-

array read, the same word of data will be output on successive clock edges until the

burst length requirements are satisfied. See During synchronous read operations, WAIT

indicates invalid data when asserted, and valid data when deasserted with respect to a

valid clock edge. See Section 7.0, “AC Characteristics” on page 26 for additional details.

10.3

Read Array

The Read Array command places (or resets) the partition in read-array mode and is

used to read data from the flash memory array. Upon initial device power-up, or after

reset (RST# transitions from VIL to VIH), all partitions default to asynchronous read-

array mode. To read array data from the flash device, first write the Read Array

command (FFh) to the CUI and specify the desired word address. Then read from that

address. If a partition is already in read-array mode, issuing the Read Array command

is not required to read from that partition.

If the Read Array command is written to a partition that is erasing or programming, the

device presents invalid data on the bus until the program or erase operation completes.

After the program or erase finishes in that partition, valid array data can then be read.

If an Erase Suspend or Program Suspend command suspends the WSM, a subsequent

Read Array command places the addressed partition in read-array mode. The Read

Array command functions independently of VPP.

10.4

Read Identifier

The Read Identifier mode outputs the manufacturer/device identifier, block lock status,

protection register codes, and Configuration Register data. The identifier information is

contained within a separate memory space on the device and can be accessed along

the 4-Mbit partition address range supplied by the Read Identifier command (90h)

address. Reads from addresses in Table 24 retrieve ID information. Issuing a Read

Identifier command to a partition that is programming or erasing places that partition’s

outputs in read ID mode while the partition continues to program or erase in the

background.

Table 24: Device Identification Codes (Sheet 1 of 2)

Item

Address1

Data

Description

Base

Offset

Manufacturer ID

Partition

00h

0089h

Numonyx

Device ID

Partition

01h

8862h

32-Mbit, Top Parameter Device

8863h

32-Mbit, Bottom Parameter Device

8864h

64-Mbit, Top Parameter Device

8865h

64-Mbit, Bottom Parameter Device

8866h

128-Mbit, Top Parameter Device

8867h

128-Mbit, Bottom Parameter Device

Block Lock Status(2)

Block

02h

D0 = 0

Block is unlocked

D0 = 1

Block is locked

Block Lock-Down Status(2)

Block

02h

D1 = 0

Block is not locked-down

D1 = 1

Block is locked down

Configuration Register

Partition

05h

PC48F4400PLVB0 数据表(PDF) 56 Page - Numonyx B.V

PC48F4400PLVB0 数据表(HTML) 56 Page - Numonyx B.V

Html Pages

1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 41 42 43 44 45 46 47 48 49 50 51 52 53 54 55 56 57 58 59 60 61 62 63 64 65 66 67 68 69 70 71 72 73 74 75 76 77 78 79 80 81 82 83 84 85 86 87 88 89 90 91 92 93 94 95 96 97 98 99 100 ...More

数据表下载

链接网址

PC48F4400PLVB0 数据表(PDF) 56 Page - Numonyx B.V

PC48F4400PLVB0 数据表(HTML) 56 Page - Numonyx B.V

Html Pages

1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 41 42 43 44 45 46 47 48 49 50 51 52 53 54 55 56 57 58 59 60 61 62 63 64 65 66 67 68 69 70 71 72 73 74 75 76 77 78 79 80 81 82 83 84 85 86 87 88 89 90 91 92 93 94 95 96 97 98 99 100 ...More

数据表 下载

链接网址

数据表下载