| 数据搜索系统,热门电子元器件搜索 |
|
ORSPI4 数据表(PDF) 69 Page - Lattice Semiconductor |
|
|
|||||||||||||||||||||||||||||
ORSPI4 数据表(HTML) 69 Page - Lattice Semiconductor |
|
69 / 263 page ![]() Lattice Semiconductor ORCA ORSPI4 Data Sheet 69 These blocks will be described in detail in the following sections. The ORSPI4 Receive functional block diagram is shown in Figure 29. Figure 29. ORSPI4 Receive Functional Block Diagram ORSPI4 Receive Functional Block Overview The ORSPI4 high-speed receive logic receives high-speed data on 16 LVDS pairs (RDAT[15:0]), control on one LVDS pair (RCTL) and clock on one LVDS pair (RDCLK) at the SPI4 interface. This is an OIF-SPI-4 02.0 compliant interface that supports data rates in the range of 622-900 Mbps. Additionally lower-speed data in the range of 100- 200 Mbps is also supported. The high-speed receive interface logic supports both static and dynamic alignment as specified by the OIF-SPI-4 02.0 specification. Dynamic alignment allows for +/- one bit period of skew. During dynamic alignment, training patterns are detected and deskew performed. Data is then deserialized into 128-bit data and 8-bit control bus. The SPI4 receive data protocol logic then extracts the control information such as PORT_ID, SOP, EOP and ERR into a separate sideband bus while still preserving wire-speed throughput. Data and control signals are then written into one of four dual-port RAMs (DPRAMs). Per-port buffering is supported for a maximum of 32 ports. The DPRAMs are built as multiple virtual FIFOs where each FIFO can be allocated for a port by the user through software. At the FPGA fabric, the user reads data for the desired ports from the FIFOs [A,B]RSTAT [A,B]RSCLK RX DPRAM SPI[A,B]_k_DATA_j, BE_j SPI[A,B]_k_SOPj, EOPj, ERRj [A,B]STOP_ON_EOPj SPI[A,B]_k_RD_j SPI[A,B]_k_ADDR_j Address SPI[A,B]_k_CLK_j Mapper RDI [A,B]RDAT [A,B]RCTL [A,B]RDCLK PSS RSP RSO SPI[A,B]_k_STAT SPI[A,B]_k_PORT_ID SPI[A,B]_k_EXT_STAT_EN SPI[A,B]_k_PSS_WE SPI[A,B]_k_PSS_CLK RLSTAT RLSCLK 16 2 2 2 8 3 3 RDP data control control data control SPI[A,B]_k_FIFO_EMPTY_j k = 32, 64 or 128 j= 0, 1, 2 or 3 SPI[A,B]_k_ CTL_j (32 and 64 only) [A,B]RLSCLK_F |
|
链接网址 |
| ALLDATASHEET是否为您带来帮助? [ DONATE ] |
关于 Alldatasheet | 广告服务 | 联系我们 | 隐私政策 | 数据表链接 | 链接交换 | 制造商名单 All Rights Reserved©Alldatasheet.com |
| Russian : Alldatasheetru.com | Korean : Alldatasheet.co.kr | Spanish : Alldatasheet.es | French : Alldatasheet.fr | Italian : Alldatasheetit.com Portuguese : Alldatasheetpt.com | Polish : Alldatasheet.pl | Vietnamese : Alldatasheet.vn Indian : Alldatasheet.in | Mexican : Alldatasheet.com.mx | British : Alldatasheet.co.uk | New Zealand : Alldatasheet.co.nz |
|
Family Site : ic2ic.com |
icmetro.com |