MPC8572ECLPXATLD datasheet(59/140 Pages) FREESCALE

59 / 140 page

MPC8572E PowerQUICC III Integrated Processor Hardware Specifications, Rev. 4

Freescale Semiconductor

Local Bus Controller (eLBC)

NOTE

In PLL bypass mode, LCLK[n] is the inverted version of the internal clock

with the delay of tLBKHKT. In this mode, signals are launched at the rising edge

of the internal clock and are captured at the falling edge of the internal clock

with the exception of LGTA/LUPWAIT (which is captured on the rising

edge of the internal clock).

LALE output negation to high impedance for

LAD/LDP (LATCH hold time)

tLBOTOT

1.5

—

Local bus clock to output valid (except LAD/LDP and

LALE)

tLBKLOV1

—–0.3

Local bus clock to data valid for LAD/LDP

tLBKLOV2

—–0.1

Local bus clock to address valid for LAD

tLBKLOV3

—0.0

Local bus clock to LALE assertion

tLBKLOV4

—0.0

Output hold from local bus clock (except LAD/LDP

and LALE)

tLBKLOX1

–3.3

—

Output hold from local bus clock for LAD/LDP

tLBKLOX2

–3.3

—

Local bus clock to output high Impedance (except

LAD/LDP and LALE)

tLBKLOZ1

—0.2

Local bus clock to output high impedance for

LAD/LDP

tLBKLOZ2

—0.2

Notes:

1. The symbols used for timing specifications herein follow the pattern of t(First two letters of functional block)(signal)(state) (reference)(state)

for inputs and t(First two letters of functional block)(reference)(state)(signal)(state) for outputs. For example, tLBIXKH1 symbolizes local bus

timing (LB) for the input (I) to go invalid (X) with respect to the time the tLBK clock reference (K) goes high (H), in this case for

clock one(1). Also, tLBKHOX symbolizes local bus timing (LB) for the tLBK clock reference (K) to go high (H), with respect to the

output (O) going invalid (X) or output hold time.

2. All timings are in reference to local bus clock for PLL bypass mode. Timings may be negative with respect to the local bus

clock because the actual launch and capture of signals is done with the internal launch/capture clock, which precedes LCLK

by tLBKHKT.

3. Maximum possible clock skew between a clock LCLK[m] and a relative clock LCLK[n]. Skew measured between

complementary signals at BVDD/2.

4. All signals are measured from BVDD/2 of the rising edge of local bus clock for PLL bypass mode to 0.4 x BVDD of the signal

in question for 3.3-V signaling levels.

5. Input timings are measured at the pin.

6. tLBOTOT is a measurement of the minimum time between the negation of LALE and any change in LAD. tLBOTOT is

programmed with the LBCR[AHD] parameter.

7. For purposes of active/float timing measurements, the Hi-Z or off state is defined to be when the total current delivered through

the component pin is less than or equal to the leakage current specification.

Table 51. Local Bus General Timing Parameters—PLL Bypassed (continued)

At recommended operating conditions with BVDD of 3.3 V ± 5%

Parameter

Symbol 1

Min

Max

Unit

Notes

MPC8572ECLPXATLD 数据表(PDF) 59 Page - Freescale Semiconductor, Inc

MPC8572ECLPXATLD 数据表(HTML) 59 Page - Freescale Semiconductor, Inc

Html Pages

1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 41 42 43 44 45 46 47 48 49 50 51 52 53 54 55 56 57 58 59 60 61 62 63 64 65 66 67 68 69 70 71 72 73 74 75 76 77 78 79 80 81 82 83 84 85 86 87 88 89 90 91 92 93 94 95 96 97 98 99 100 ...More

数据表下载