 |
数据搜索系统，热门电子元器件搜索 |
|
|
数据搜索系统，热门电子元器件搜索 |
|
TMS320DM8167 数据表(PDF) 72 Page - Texas Instruments |
|
|
|
|||||||||||||||||||||||||||||
TMS320DM8167 数据表(HTML) 72 Page - Texas Instruments |
|
|
72 / 312 page  TMS320DM8168, TMS320DM8167 TMS320DM8166, TMS320DM8165 SPRS614 – MARCH 2011 www.ti.com 3.2.6 High-Definition Multimedia Interface (HDMI) Signals Table 3-7. HDMI Terminal Functions SIGNAL TYPE(1) OTHER(2) (3) MUXED DESCRIPTION NAME NO. - HDMI Clock Output. HDMI_TMDSCLKP AT24 O - VDDA_HDMI When the HDMI PHY is powered down, these pins - HDMI_TMDSCLKN AU24 O - should be left unconnected. VDDA_HDMI - HDMI Data 2 output. HDMI_TMDSDN2 AU27 O - VDDA_HDMI When the HDMI PHY is powered down, these pins - HDMI_TMDSDP2 AT27 O - should be left unconnected. VDDA_HDMI - HDMI Data 1 output. HDMI_TMDSDN1 AU26 O - VDDA_HDMI When the HDMI PHY is powered down, these pins - HDMI_TMDSDP1 AT26 O - should be left unconnected. VDDA_HDMI - HDMI Data 0 output. HDMI_TMDSDN0 AU25 O - VDDA_HDMI When the HDMI PHY is powered down, these pins - HDMI_TMDSDP0 AT25 O - should be left unconnected. VDDA_HDMI PULL: DIS / DIS - HDMI_SCL AL25 O DRIVE: Z / Z HDMI I2C Serial Clock Output PINCTRL301 DVDD_3P3 PULL: DIS / DIS - HDMI_SDA AK25 I/O DRIVE: Z / Z HDMI I2C Serial Data I/O PINCTRL302 DVDD_3P3 PULL: IPU / IPU - HDMI_CEC AP25 I/O DRIVE: H / H HDMI Consumer Electronics Control I/O PINCTRL303 DVDD_3P3 PULL: IPD / IPD HDMI Hot Plug Detect Input. Signals the - HDMI_HPDET AE24 I DRIVE: Z / Z connection / removal of an HDMI cable at the PINCTRL304 DVDD_3P3 connector. HDMI Voltage Reference. When HDMI is used, this pin must be connected via an external 698- Ω (±1% tolerance) resistor to VSS. HDMI_EXTSWING AN25 A - - When the HDMI PHY is powered down, this pin should be left unconnected. (1) I = Input, O = Output, Z = High impedance, S = Supply voltage, GND = Ground, A = Analog signal. (2) PULL: A / B, where: A is the state of the internal pull resistor during POR reset B is the state of the internal pull resistor after POR and Warm reset are de-asserted and during Warm reset IPD = Internal Pulldown Enabled, IPU = Internal Pullup Enabled, DIS = Internal Pull Disabled DRIVE: A / B, where; A is the driving state of the pin during POR reset B is the driving state of the pin after POR and Warm reset are de-asserted and during Warm reset H = Driving High, L = Driving Low, Z = 3-State For more detailed information on pullup/pulldown resistors and situations where external pullup/pulldown resistors are required, see Section 4.2.1, Pullup/Pulldown Resistors. (3) Specifies the operating I/O supply voltage for each signal. 72 Device Pins Copyright © 2011, Texas Instruments Incorporated Submit Documentation Feedback Product Folder Link(s): TMS320DM8168 TMS320DM8167 TMS320DM8166 TMS320DM8165 |
|
链接网址 |
| ALLDATASHEET是否为您带来帮助? [ DONATE ] |
关于 Alldatasheet | 广告服务 | 联系我们 | 隐私政策 | 数据表链接 | 链接交换 | 制造商名单 All Rights Reserved©Alldatasheet.com |
| Russian : Alldatasheetru.com | Korean : Alldatasheet.co.kr | Spanish : Alldatasheet.es | French : Alldatasheet.fr | Italian : Alldatasheetit.com Portuguese : Alldatasheetpt.com | Polish : Alldatasheet.pl | Vietnamese : Alldatasheet.vn Indian : Alldatasheet.in | Mexican : Alldatasheet.com.mx | British : Alldatasheet.co.uk | New Zealand : Alldatasheet.co.nz |
|
Family Site : ic2ic.com |
icmetro.com |
Chinese ▼
English
Chinese
German
Japanese
Russian
Korean
Spanish
French
Italian
Portuguese
Polish
Vietnamese
Indian
Mexican
British
New Zealand
