MPC5643L datasheet(135/136 Pages) FREESCALE

135 / 136 page

Document revision history

MPC5643L Microcontroller Data Sheet, Rev. 8.1

Freescale Semiconductor

135

• Added Table 29 (MPC5643L SWG Specifications)

•In Table 29 (MPC5643L SWG Specifications)

Added table footnote for Common Mode.

Changed text from “internal device pad resistance” to “internal device routing resistance”.

• Added Figure 26 in Section 3.20.4, “Nexus timing”.

•In Table 30 (Pad AC specifications (3.3 V , IPP_HVE = 0 )), removed the row of pad

“Pull Up/Downc(3.6 V max)”.

•In Table 40 (Orderable part number summary) and Figure 43, updated part numbers

(changed ‘PPC’ to ‘SPC’ and ‘F0’ to ‘F2’).

• Replaced Figure 39, Figure 40, Figure 41, Figure 42 with the new versions.

•InTable 18 (Voltage regulator electrical specifications),changed the symbol of spec

external decoupling capacitor from SR to Cext.

In Figure 4, changed the ESR range in note text to 1 mW to 100 mW from 30 mW to

150 mW.

•In Section 1.5.32, “Sine Wave Generator (SWG)” removed the following text:

Frequency range from 1kHz to 50kHz.

Sine wave amplitude from 0.47 V to 2.26 V.

•In Table 20 (Current consumption characteristics)”,changed symbol from ‘C’ to ‘T’ ,

added “operating current” to the parameter and updated the maximum value for five

additional RunIDD parameters.

•In Table 20 (Current consumption characteristics), changed “Conditions” from ‘1.2 V

supplies’ to ‘1.2 V supplies during LBIST (full LBIST configuration)’ for all the

parameters.

• Removed Table “SWG electrical characteristics”.

•In Table 18 (Voltage regulator electrical specifications), changed the “Digital supply

high voltage detector upper threshold low limit (After a destructive reset initialization

phase completion)” from 1.43V to 1.38V.

• Added Table 17 (Recommended operating characteristics).

• Updated the IDD values in Table 20 (Current consumption characteristics). Changed

conditions text from “1.2 supplies during LBIST (full LBIST configuration)” to “1.2 V

supplies” for all the IDD parameters except IDD_LV_BIST+IDD_LV_PLL. Added footnote in

“Conditions” for the DPM mode.

• Removed Cut references from the whole document.

•In Table 25 (ADC conversion characteristics), changed the sampling frequency value

from ‘1 MHz’ to ‘983.6 KHz’.

8.1

07 May 2012

• Deleted the Footer "Preliminary-Subject to Change Without Notice" label.

Table 41. Revision history (continued)

Revision

Date

Description of changes

MPC5643L 数据表(PDF) 135 Page - Freescale Semiconductor, Inc

MPC5643L 数据表(HTML) 135 Page - Freescale Semiconductor, Inc

Html Pages

1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 41 42 43 44 45 46 47 48 49 50 51 52 53 54 55 56 57 58 59 60 61 62 63 64 65 66 67 68 69 70 71 72 73 74 75 76 77 78 79 80 81 82 83 84 85 86 87 88 89 90 91 92 93 94 95 96 97 98 99 100 ...More

数据表下载