CMX608 datasheet(41/70 Pages) CMLMICRO

41 / 70 page

RALCWI Vocoder

CMX608/CMX618/CMX638

 2014 CML Microsystems Plc

D/608_18_38/11

$07 (ECC_CODEC_START)

Starts the CODEC running. The exact effect of this command is CODEC dependant. If any of the

generic CODEC settings are chosen, this command does not do anything. Please refer to the

external CODEC support section.

$08 (ECC_CODEC_PSAVE)

Places the CODEC in a powersave state.

The exact effect of this command is CODEC

dependant.

If any of the generic CODEC settings are chosen, this command does not do

anything. Please refer to the external CODEC support section.

$09 (ECC_EEC_LOW)

Set the output port EEC low, without affecting the REC port. Using this command removes the

need to hold a shadow register for the port states.

$0A (ECC_EEC_HIGH)

Set the output port EEC high, without affecting the REC port. Using this command removes the

need to hold a shadow register for the port states.

$0B (ECC_REC_LOW)

Set the output port REC low, without affecting the EEC port. Using this command removes the

need to hold a shadow register for the port states.

$0C (ECC_REC_HIGH)

Set the output port REC high, without affecting the EEC port. Using this command removes the

need to hold a shadow register for the port states.

$0D - $3F Reserved.

SEL1 / SEL0 = '11' - Reserved

reserved

IDD register address $0C

Delay

This write-only register controls an initial delay in sending samples to the CODEC after the first

frame is given to the decoder, once it has been enabled. The value is given in samples (125µs)

and must be between 1 and 255 inclusive. This register has a default value of 64, which equates

to a time period of 8ms. Bit 7 is the msb.

Once the delay has been set, bit 15 (RDY) of the STATUS register ($40) will be set and IRQN will

go low if C-BUS interrupts are enabled for this bit. After the decoder is enabled, the first frame

that is given to the device for decoding will start a delay timer primed with the value contained in

this register. The device will not attempt to send a sample to the CODEC until this timer reaches

zero. After the timer has expired, it will not be used again until the decoder is disabled, and then

re-enabled, where receipt of the first frame will again start the timer.

This delay period is required in order to eliminate the effect of the algorithmic jitter in the decoder

algorithm. If additional algorithmic jitter is present in frame acquisition and presentation (perhaps

from a demodulator, or from scheduling effects in the host) then this delay may need to be

increased to prevent the CODEC from suffering sample starvation during the first few frames.

Please see section 5.3 for further information.

CMX608 数据表(PDF) 41 Page - CML Microcircuits

CMX608 数据表(HTML) 41 Page - CML Microcircuits

Html Pages

1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 41 42 43 44 45 46 47 48 49 50 51 52 53 54 55 56 57 58 59 60 61 62 63 64 65 66 67 68 69 70

数据表下载

链接网址

CMX608 数据表(PDF) 41 Page - CML Microcircuits

CMX608 数据表(HTML) 41 Page - CML Microcircuits

Html Pages

1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 41 42 43 44 45 46 47 48 49 50 51 52 53 54 55 56 57 58 59 60 61 62 63 64 65 66 67 68 69 70

数据表 下载

链接网址

数据表下载