STM32F756VG datasheet(23/228 Pages) STMICROELECTRONICS

23 / 228 page

DocID027589 Rev 4

23/228

STM32F756xx

Functional overview

2.15

Boot modes

At startup, the boot memory space is selected by the BOOT pin and BOOT_ADDx option

bytes, allowing to program any boot memory address from 0x0000 0000 to 0x3FFF FFFF

which includes:

•

All Flash address space mapped on ITCM or AXIM interface

•

All RAM address space: ITCM, DTCM RAMs and SRAMs mapped on AXIM interface

•

The System memory bootloader

The boot loader is located in system memory. It is used to reprogram the Flash memory

through a serial interface.

2.16

Power supply schemes

•

VBAT = 1.65 to 3.6 V: power supply for RTC, external clock 32 kHz oscillator and

backup registers (through power switch) when VDD is not present.

•

VDD = 1.7 to 3.6 Vexternal power supply for I/Os and the internal regulator (when

enabled), provided externally through VDD pins.

•

VSSA, VDDA = 1.7 to 3.6 V: external analog power supplies for ADC, DAC, reset blocks,

RCs and PLL. VDDA and VSSA must be connected to VDD and VSS, respectively.

Note:

VDD/VDDA minimum value of 1.7 V is obtained when the internal reset is OFF (refer to

Section 2.17.2: Internal reset OFF). Refer to Table 3: Voltage regulator configuration mode

versus device operating mode to identify the packages supporting this option.

•

VDDUSB can be connected either to VDD or an external independent power supply (3.0

to 3.6V) for USB transceivers (refer to Figure 4 and Figure 5). For example, when

device is powered at 1.8V, an independent power supply 3.3V can be connected to

VDDUSB. When the VDDUSB is connected to a separated power supply, it is independent

from VDD or VDDA but it must be the last supply to be provided and the first to

disappear. The following conditions VDDUSB must be respected:

–

During power-on phase (VDD < VDD_MIN), VDDUSB should be always lower than

VDD

–

During power-down phase (VDD < VDD_MIN), VDDUSB should be always lower than

VDD

–VDDSUB rising and falling time rate specifications must be respected (see Table 20

and Table 21)

–

In operating mode phase, VDDUSB could be lower or higher than VDD:

- If USB (USB OTG_HS/OTG_FS) is used, the associated GPIOs powered by

VDDUSB are operating between VDDUSB_MIN and VDDUSB_MAX.

- The VDDUSB supply both USB transceiver (USB OTG_HS and USB OTG_FS). If

only one USB transceiver is used in the application, the GPIOs associated to the

other USB transceiver are still supplied by VDDUSB.

- If USB (USB OTG_HS/OTG_FS) is not used, the associated GPIOs powered by

VDDUSB are operating between VDD_MIN and VDD_MAX.

STM32F756VG 数据表(PDF) 23 Page - STMicroelectronics

STM32F756VG 数据表(HTML) 23 Page - STMicroelectronics

Html Pages

1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 41 42 43 44 45 46 47 48 49 50 51 52 53 54 55 56 57 58 59 60 61 62 63 64 65 66 67 68 69 70 71 72 73 74 75 76 77 78 79 80 81 82 83 84 85 86 87 88 89 90 91 92 93 94 95 96 97 98 99 100 ...More

数据表下载