STM32F303VC datasheet(58/148 Pages) STMICROELECTRONICS

58 / 148 page

Electrical characteristics

STM32F303xB STM32F303xC

58/148

DocID023353 Rev 13

2. VREF+ must be always lower or equal than VDDA (VREF+ ≤VDDA). If unused then it must be connected to VDDA.

3. VIN maximum must always be respected. Refer to Table 22: Current characteristics for the maximum allowed injected

current values.

4. Include VREF- pin.

Table 22. Current characteristics

Symbol

Ratings

Max.

Unit

ΣIVDD

Total current into sum of all VDD power lines (source)

160

ΣIVSS

Total current out of sum of all VSS ground lines (sink)

−160

IVDD

Maximum current into each VDD power line (source)(1)

100

IVSS

Maximum current out of each VSS ground line (sink)(1)

−100

IIO(PIN)

Output current sunk by any I/O and control pin

Output current source by any I/O and control pin

−25

ΣIIO(PIN)

Total output current sunk by sum of all IOs and control pins(2)

Total output current sourced by sum of all IOs and control pins(2)

−80

IINJ(PIN)

Injected current on FT, FTf and B pins(3)

-5/+0

Injected current on TC and RST pin(4)

± 5

Injected current on TTa pins(5)

± 5

ΣIINJ(PIN)

Total injected current (sum of all I/O and control pins)(6)

± 25

1. All main power (VDD, VDDA) and ground (VSS and VSSA) pins must always be connected to the external power supply, in the

permitted range.

2. This current consumption must be correctly distributed over all I/Os and control pins.The total output current must not be

sunk/sourced between two consecutive power supply pins referring to high pin count LQFP packages.

3. Positive injection is not possible on these I/Os and does not occur for input voltages lower than the specified maximum

value.

4. A positive injection is induced by VIN > VDD while a negative injection is induced by VIN< VSS. IINJ(PIN) must never be

exceeded. Refer to Table 21: Voltage characteristics for the maximum allowed input voltage values.

5. A positive injection is induced by VIN > VDDA while a negative injection is induced by VIN< VSS. IINJ(PIN) must never be

exceeded. Refer also to Table 21: Voltage characteristics for the maximum allowed input voltage values. Negative injection

disturbs the analog performance of the device. See note (2) below Table 70.

6. When several inputs are submitted to a current injection, the maximum

ΣIINJ(PIN) is the absolute sum of the positive and

negative injected currents (instantaneous values).

Table 23. Thermal characteristics

Symbol

Ratings

Value

Unit

TSTG

Storage temperature range

–65 to +150

°C

Maximum junction temperature

150

°C

STM32F303VC 数据表(PDF) 58 Page - STMicroelectronics

STM32F303VC 数据表(HTML) 58 Page - STMicroelectronics

Html Pages

1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 41 42 43 44 45 46 47 48 49 50 51 52 53 54 55 56 57 58 59 60 61 62 63 64 65 66 67 68 69 70 71 72 73 74 75 76 77 78 79 80 81 82 83 84 85 86 87 88 89 90 91 92 93 94 95 96 97 98 99 100 ...More

数据表下载