4200A-SCS Parameter Analyzer

10V Range

40V Range

1 Ω

0.196 V

196 mA

0.784 V

784 mA

5 Ω

0.909 V

182 mA

3.64 V

727 mA

10 Ω

1.67 V

167 mA

6.67 V

667 mA

25 Ω

3.33 V

133 mA

13.3 V

533 mA

50 Ω

5.00 V

100 mA

20.0 V

400 mA

100 Ω

6.67 V

66.7 mA

26.7 V

267 mA

250 Ω

8.33 V

33.3 mA

33.3 V

133 mA

1 kΩ

9.52 V

9.5 mA

38.1 V

38.1 mA

10 kΩ

9.95 V

995 μA

39.8 V

3.98 mA

Notes

1. To calculate the approximate maximum current and voltage for any resistance

I

V

where Resistance is the total resistance connected to the PMU or PGU channel and V range is either 10 or 40.

Example: 10 V range using R = 10 Ω (for DUT + interconnect)

V

2. Typical maximum at pulse output connector. Resistance is the total resistance connected to the pulse output connector, including device

and interconnect.

I

I

V

V

10

9

8

7

6

5

4

3

2

1

0

1

100

10000

DUT Resistance (

Ω)

10V Range: Max. Output vs. DUT Resistance

0.20

0.18

0.16

0.14

0.12

0.10

0.08

0.06

0.04

0.02

0.00

I

I

V

V

40

35

30

25

20

15

10

5

0

1

100

10000

DUT Resistance (

Ω)

40V Range: Max. Output vs. DUT Resistance

0.8

0.7

0.6

0.5

0.4

0.3

0.2

0.1

0.0

10 V Range

40 V Range

V

OUT

50 Ω into 1 MΩ

–10 V to +10 V

–40 V to +40 V

50 Ω into 50 Ω

–5 V to +5 V

–20 V to +20 V

Accuracy

±(0.5% + 10 mV)

±(0.2% + 20 mV)

Resolution

50 Ω into 50 Ω

<250 µV

<750 µV

50 Ω into 1 MΩ

<0.05 mV

<1.5 mV

50 Ω into 50 Ω

±(3% + 20 mV)

±(3% + 80 mV)

50 Ω into 50 Ω, typical best case

±(2% + 20 mV)

±(0.8% + 40 mV)

Baseline noise

±(0.3% + 1 mV) RMS typical

±(0.1% + 5 mV) RMS typical

Source impedance

50 Ω nominal

50 Ω nominal

Current into 50Ω load (at full scale)

±100 mA typical

±400 mA typical

Short circuit current

±200 mA

±800 mA

Output limit

Programmable limit to protect the device under test

Notes

1. Unless stated otherwise, all specifications assume a 50 Ω termination.

2. Level specifications are valid after 50 ns typical settling time (after slewing) for the 10 V source range and after 500 ns typical settling time (after slewing) for the 40 V source range into a 50 Ω load.

3. With transition time of 20 ns (0%–100%) for the 10 V source range and 100 ns (0% to 100%) for the 40 V source range.