ADV7393 datasheet(55/96 Pages) AD

55 / 96 page

ADV7390/ADV7391/ADV7392/ADV7393

Rev. 0 | Page 55 of 96

ED/HD SHARPNESS FILTER AND ADAPTIVE FILTER

CONTROLS

Subaddress 0x40, Subaddress 0x58 to Subaddress 0x5D

There are three filter modes available on the ADV739x:

sharpness filter mode and two adaptive filter modes.

ED/HD Sharpness Filter Mode

To enhance or attenuate the Y signal in the frequency ranges

shown in Figure 74, the ED/HD sharpness filter must be

enabled (Subaddress 0x31, Bit 7 = 1) and the ED/HD adaptive

filter must be disabled (Subaddress 0x35, Bit 7 = 0).

To select one of the 256 individual responses, the corresponding

gain values, ranging from −8 to +7 for each filter, must be

programmed into the ED/HD sharpness filter gain register at

Subaddress 0x40.

ED/HD Adaptive Filter Mode

In ED/HD adaptive filter mode, the following registers are used:

•

ED/HD Adaptive Filter Threshold A

•

ED/HD Adaptive Filter Threshold B

•

ED/HD Adaptive Filter Threshold C

•

ED/HD Adaptive Filter Gain 1

•

ED/HD Adaptive Filter Gain 2

•

ED/HD Adaptive Filter Gain 3

•

ED/HD sharpness filter gain register

To activate the adaptive filter control, the ED/HD sharpness

filter and the ED/HD adaptive filter must be enabled

(Subaddress 0x31, Bit 7 = 1, and Subaddress 0x35, Bit 7 = 1,

respectively).

The derivative of the incoming signal is compared to the three

programmable threshold values: ED/HD Adaptive Filter

Threshold A, Threshold B, and Threshold C (Subaddress 0x5B,

Subaddress 0x5C, and Subaddress 0x5D). The recommended

threshold range is 16 to 235, although any value in the range of

0 to 255 can be used.

The edges can then be attenuated with the settings in the

ED/HD Adaptive Filter Gain 1, Gain 2, and Gain 3 registers

(Subaddress 0x58, Subaddress 0x59 and Subaddress 0x5A), and

the ED/HD sharpness filter gain register (Subaddress 0x40).

There are two adaptive filter modes available. The mode is

selected using the ED/HD adaptive filter mode control

(Subaddress 0x35, Bit 6):

•

Mode A is used when the ED/HD adaptive filter mode

control is set to 0. In this case, Filter B (LPF) is used in the

adaptive filter block. In addition, only the programmed

values for Gain B in the ED/HD sharpness filter gain

Gain 3 registers are applied when needed. The Gain A

values are fixed and cannot be changed.

•

Mode B is used when ED/HD adaptive filter mode control is

set to 1. In this mode, a cascade of Filter A and Filter B is used.

Both settings for Gain A and Gain B in the ED/HD sharpness

filter gain register and ED/HD Adaptive Filter Gain 1, Gain 2,

and Gain 3 registers become active when needed.

FREQUENCY (MHz)

FILTER A RESPONSE (Gain Ka)

0.5

0.6

0.7

0.8

0.9

1.0

1.1

1.2

1.3

1.4

1.5

FREQUENCY (MHz)

FILTER B RESPONSE (Gain Kb)

0.5

0.6

0.7

0.8

0.9

1.0

1.1

1.2

1.3

1.4

1.5

FREQUENCY (MHz)

1.0

1.1

1.2

1.3

1.4

1.5

1.6

INPUT

SIGNAL:

STEP

FREQUENCY RESPONSE IN SHARPNESS

FILTER MODE WITH Ka = 3 AND Kb = 7

SHARPNESS AND ADAPTIVE FILTER CONTROL BLOCK

Figure 74. ED/HD Sharpness and Adaptive Filter Control Block

ADV7393 数据表(PDF) 55 Page - Analog Devices

ADV7393 数据表(HTML) 55 Page - Analog Devices

Html Pages

1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 41 42 43 44 45 46 47 48 49 50 51 52 53 54 55 56 57 58 59 60 61 62 63 64 65 66 67 68 69 70 71 72 73 74 75 76 77 78 79 80 81 82 83 84 85 86 87 88 89 90 91 92 93 94 95 96

数据表下载

链接网址

ADV7393 数据表(PDF) 55 Page - Analog Devices

ADV7393 数据表(HTML) 55 Page - Analog Devices

Html Pages

1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 41 42 43 44 45 46 47 48 49 50 51 52 53 54 55 56 57 58 59 60 61 62 63 64 65 66 67 68 69 70 71 72 73 74 75 76 77 78 79 80 81 82 83 84 85 86 87 88 89 90 91 92 93 94 95 96

数据表 下载

链接网址

数据表下载