CC2500-RTR1 datasheet(80/84 Pages) TI

80 / 84 page

CC2500

PRELIMINARY Data Sheet (Rev.1.2)

SWRS040A

Page 80 of 83

32.5

Carrier tape and reel specification

Carrier tape and reel is in accordance with EIA Specification 481.

Tape and Reel Specification

Package

Tape Width

Component

Pitch

Hole

Pitch

Reel

Diameter

Units per Reel

QLP 20

12 mm

8 mm

4 mm

13 inches

2500

Table 41: Carrier tape and reel specification

33 Ordering Information

Chipcon Part

Number

TI Part Number

Description

Minimum Order Quantity

(MOQ)

CC2500-RTY1

CC2500RTK

CC2500 QLP20 RoHS Pb-free 490/tray

490 (tray)

CC2500-RTR1

CC2500RTKR

CC2500 QLP20 RoHS Pb-free 2500/T&R

2500 (tape and reel)

CC2500-CC2550DK

CC2500_CC2550 Development Kit

CC2500EMK

CC2500 Evaluation Module Kit

Table 42: Ordering information

34 General Information

34.1

Document History

Revision

Date

Description/Changes

1.2

2006-06-28 Added figures to table on SPI interface timing requirements.

Added information about SPI read.

Updates to text and included new figure in section on arbitrary length configuration.

Updates to section on CRC check. Added information about CRC check when

PKTCTRL0.CC2400_EN=1.

Added information on RSSI update rate in section RSSI.

Updates to text and included new figures in section on power-on start-up sequence.

Changes to wake-on-radio current consumption figures under electrical specifications.

Updates to text in section on data FIFO.

Added information about how to check for PLL lock in section on VCO.

Better explanation of some of the signals in table of GDO signal selection. Also added some more

signals.

Added section on wideband modulation not using spread spectrum under section on system

considerations and guidelines.

Changes to timeout for sync word search in RX in register MCSM2.

Changes to wake-on-radio control register WORCTRL. WOR_RES[1:0] settings 10 b and 11b

changed to Not Applicable (NA).

Added more detailed information on PO_TIMEOUT in register MCSM0.

Added description of programming bits in registers FOCCFG, BSCFG, AGCCTRL0, FREND1.

Changes to ordering information.

1.1

2005-10-20 MDMCFG2[7] used. 26-27 MHz crystal range. Chapter 15: description of the 2 optional append

bytes. Added matching information. Added information about using a reference signal instead of a

crystal. CRC can only be checked by append bytes or CRC_AUTOFLUSH. Added equation for

calculating RSSI in dBm. Selectivity performance graphs added.

1.0

2005-01-24 First preliminary release.

Table 43: Document history

CC2500-RTR1 数据表(PDF) 80 Page - Texas Instruments

CC2500-RTR1 数据表(HTML) 80 Page - Texas Instruments

Html Pages

1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 41 42 43 44 45 46 47 48 49 50 51 52 53 54 55 56 57 58 59 60 61 62 63 64 65 66 67 68 69 70 71 72 73 74 75 76 77 78 79 80 81 82 83 84

数据表下载