M38C31M7AXXXFS datasheet(74/224 Pages) RENESAS

74 / 224 page

2-9

APPLICATION

2.1 I/O port

38C3 Group User’s Manual

2.1.5 Termination of unused pins

(1)

Terminate unused pins

Output ports : Open

Input ports :

Connect each pin to VCC or VSS through each resistor of 1 k

Ω to 10 kΩ.

As for pins whose potential affects to operation modes such as pin INT or others, select the VCC

pin or the VSS pin according to their operation mode.

I/O ports :

• Set the I/O ports for the input mode and connect them to VCC or VSS through each resistor of

1 k

Ω to 10 kΩ.

Ports that permit the selecting of a built-in pull-up resistor can also use this resistor. Set the

I/O ports for the output mode and open them at “L” or “H”.

• When opening them in the output mode, the input mode of the initial status remains until the

mode of the ports is switched over to the output mode by the program after reset. Thus, the

potential at these pins is undefined and the power source current may increase in the input

mode. With regard to an effects on the system, thoroughly perform system evaluation on the user

side.

• Since the direction register setup may be changed because of a program runaway or noise, set

direction registers by program periodically to increase the reliability of program.

(2)

Termination remarks

Input ports and I/O ports :

Do not open in the input mode.

q Reason

• The power source current may increase depending on the first-stage circuit.

• An effect due to noise may be easily produced as compared with proper termination and

shown on the above.

I/O ports :

When setting for the input mode, do not connect to VCC or VSS directly.

q Reason

If the direction register setup changes for the output mode because of a program runaway or

noise, a short circuit may occur between a port and VCC (or VSS).

I/O ports :

When setting for the input mode, do not connect multiple ports in a lump to VCC or VSS through

a resistor.

q Reason

If the direction register setup changes for the output mode because of a program runaway or

noise, a short circuit may occur between ports.

• At the termination of unused pins, perform wiring at the shortest possible distance (20 mm or less)

from microcomputer pins.

M38C31M7AXXXFS 数据表(PDF) 74 Page - Renesas Technology Corp

M38C31M7AXXXFS 数据表(HTML) 74 Page - Renesas Technology Corp

Html Pages

1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 41 42 43 44 45 46 47 48 49 50 51 52 53 54 55 56 57 58 59 60 61 62 63 64 65 66 67 68 69 70 71 72 73 74 75 76 77 78 79 80 81 82 83 84 85 86 87 88 89 90 91 92 93 94 95 96 97 98 99 100 ...More

数据表下载

链接网址

M38C31M7AXXXFS 数据表(PDF) 74 Page - Renesas Technology Corp

M38C31M7AXXXFS 数据表(HTML) 74 Page - Renesas Technology Corp

Html Pages

1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 41 42 43 44 45 46 47 48 49 50 51 52 53 54 55 56 57 58 59 60 61 62 63 64 65 66 67 68 69 70 71 72 73 74 75 76 77 78 79 80 81 82 83 84 85 86 87 88 89 90 91 92 93 94 95 96 97 98 99 100 ...More

数据表 下载

链接网址

数据表下载