| 数据搜索系统,热门电子元器件搜索 |
|
MPC8536EBVTATH 数据表(PDF) 58 Page - Freescale Semiconductor, Inc |
|
|
|||||||||||||||||||||||||||||
MPC8536EBVTATH 数据表(HTML) 58 Page - Freescale Semiconductor, Inc |
|
58 / 128 page ![]() MPC8536E PowerQUICC™ III Integrated Processor Hardware Specifications, Rev. 2 Ethernet: Enhanced Three-Speed Ethernet (eTSEC), MII Management Freescale Semiconductor 58 2.9.3.4 SGMII AC Timing Specifications This section describes the SGMII transmit and receive AC timing specifications. Transmitter and receiver characteristics are measured at the transmitter outputs (SD2_TX[n] and SD2_TX[n]) or at the receiver inputs (SD2_RX[n] and SD2_RX[n]) as depicted in Figure 32 respectively. 2.9.3.4.1 SGMII Transmit AC Timing Specifications Table 41 provides the SGMII transmit AC timing targets. A source synchronous clock is not provided. Loss of signal threshold LSTS = 0 VLOS 30 — 100 mV 3, 4 LSTS = 1 65 — 175 Input AC common mode voltage VCM_ACp-p —— 100 mV 5 Receiver differential input impedance ZRX_DIFF 80 100 120 Ω — Receiver common mode input impedance ZRX_CM 20 — 35 Ω — Common mode input voltage VCM —Vxcorevss —V 6 Notes: 1. Input must be externally AC-coupled. 2. VRX_DIFFp-p is also referred to as peak to peak input differential voltage 3. The concept of this parameter is equivalent to the Electrical Idle Detect Threshold parameter in PCI Express. See PCI Express Differential Receiver (RX) Input Specifications section for further explanation. 4. The LSTS shown in the table refers to the LSTSA or LSTSE bit field of MPC8536’s SerDes 2 Control Register. 5. VCM_ACp-p is also referred to as peak to peak AC common mode voltage. 6. On-chip termination to S2GND (xcorevss). Table 41. SGMII Transmit AC Timing Specifications At recommended operating conditions with X2VDD = 1.0V ± 5%. Parameter Symbol Min Typ Max Unit Notes Deterministic Jitter JD — — 0.17 UI p-p — Total Jitter JT — — 0.35 UI p-p — Unit Interval UI 799.92 800 800.08 ps 1 VOD fall time (80%-20%) tfall 50 — 120 ps — VOD rise time (20%-80%) trise 50 — 120 ps — Notes: 1. Each UI is 800 ps ± 100 ppm. Table 40. SGMII DC Receiver Electrical Characteristics (continued) Parameter Symbol Min Typ Max Unit Notes |
|
链接网址 |
| ALLDATASHEET是否为您带来帮助? [ DONATE ] |
关于 Alldatasheet | 广告服务 | 联系我们 | 隐私政策 | 数据表链接 | 链接交换 | 制造商名单 All Rights Reserved©Alldatasheet.com |
| Russian : Alldatasheetru.com | Korean : Alldatasheet.co.kr | Spanish : Alldatasheet.es | French : Alldatasheet.fr | Italian : Alldatasheetit.com Portuguese : Alldatasheetpt.com | Polish : Alldatasheet.pl | Vietnamese : Alldatasheet.vn Indian : Alldatasheet.in | Mexican : Alldatasheet.com.mx | British : Alldatasheet.co.uk | New Zealand : Alldatasheet.co.nz |
|
Family Site : ic2ic.com |
icmetro.com |