80C32EBAA datasheet(41/62 Pages) PHILIPS

41 / 62 page

Philips Semiconductors

Product specification

80C52/80C54/80C58

CMOS single-chip 8-bit microcontrollers

1996 Aug 16

OSC

÷ 2

C/T2 = 0

C/T2 = 1

TR2

Control

TL2

(8-bits)

TH2

(8-bits)

÷ 16

RCAP2L

RCAP2H

EXEN2

Control

EXF2

Timer 2

Interrupt

T2EX Pin

Transition

Detector

T2 Pin

Reload

NOTE: OSC. Freq. is divided by 2, not 12.

÷ 2

“0”

“1”

RX Clock

÷ 16

TX Clock

“0”

“1”

“0”

“1”

Timer 1

Overflow

Note availability of additional external interrupt.

SMOD

RCLK

TCLK

SU00068

Figure 6. Timer 2 in Baud Rate Generator Mode

Table 3.

Timer 2 Generated Commonly Used

Baud Rates

Baud Rate

Osc Freq

Timer 2

Baud Rate

Osc Freq

RCAP2H

RCAP2L

375K

12MHz

9.6K

12MHz

2.8K

12MHz

2.4K

12MHz

1.2K

12MHz

300

12MHz

110

12MHz

300

6MHz

110

6MHz

Baud Rate Generator Mode

Bits TCLK and/or RCLK in T2CON (Table 2) allow the serial port

transmit and receive baud rates to be derived from either Timer 1 or

Timer 2. When TCLK= 0, Timer 1 is used as the serial port transmit

baud rate generator. When TCLK= 1, Timer 2 is used as the serial

port transmit baud rate generator. RCLK has the same effect for the

serial port receive baud rate. With these two bits, the serial port can

have different receive and transmit baud rates – one generated by

Timer 1, the other by Timer 2.

Figure 6 shows the Timer 2 in baud rate generation mode. The baud

rate generation mode is like the auto-reload mode,in that a rollover

in TH2 causes the Timer 2 registers to be reloaded with the 16-bit

value in registers RCAP2H and RCAP2L, which are preset by

software.

The baud rates in modes 1 and 3 are determined by Timer 2’s

overflow rate given below:

Modes 1 and 3 Baud Rates

+ Timer 2 Overflow Rate

The timer can be configured for either “timer” or “counter” operation.

In many applications, it is configured for “timer” operation (C/T2*=0).

Timer operation is different for Timer 2 when it is being used as a

baud rate generator.

Usually, as a timer it would increment every machine cycle (i.e., 1/12

the oscillator frequency). As a baud rate generator, it increments

every state time (i.e., 1/2 the oscillator frequency). Thus the baud

rate formula is as follows:

Oscillator Frequency

[32

[65536

* (RCAP2H, RCAP2L)]]

Modes 1 and 3 Baud Rates =

Where:

(RCAP2H, RCAP2L)= The content of RCAP2H and

RCAP2L taken as a 16-bit unsigned integer.

The Timer 2 as a baud rate generator mode shown in Figure 6, is

valid only if RCLK and/or TCLK = 1 in T2CON register. Note that a

rollover in TH2 does not set TF2, and will not generate an interrupt.

Thus, the Timer 2 interrupt does not have to be disabled when

Timer 2 is in the baud rate generator mode. Also if the EXEN2

(T2 external enable flag) is set, a 1-to-0 transition in T2EX

(Timer/counter 2 trigger input) will set EXF2 (T2 external flag) but

will not cause a reload from (RCAP2H, RCAP2L) to (TH2,TL2).

Therefore when Timer 2 is in use as a baud rate generator, T2EX

can be used as an additional external interrupt, if needed.

80C32EBAA 数据表(PDF) 41 Page - NXP Semiconductors

80C32EBAA 数据表(HTML) 41 Page - NXP Semiconductors

Html Pages

1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 41 42 43 44 45 46 47 48 49 50 51 52 53 54 55 56 57 58 59 60 61 62

数据表下载

链接网址

80C32EBAA 数据表(PDF) 41 Page - NXP Semiconductors

80C32EBAA 数据表(HTML) 41 Page - NXP Semiconductors

Html Pages

1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 41 42 43 44 45 46 47 48 49 50 51 52 53 54 55 56 57 58 59 60 61 62

数据表 下载

链接网址

数据表下载