80C32EBAA datasheet(42/62 Pages) PHILIPS

42 / 62 page

Philips Semiconductors

Product specification

80C52/80C54/80C58

CMOS single-chip 8-bit microcontrollers

1996 Aug 16

When Timer 2 is in the baud rate generator mode, one should not try

to read or write TH2 and TL2. As a baud rate generator, Timer 2 is

incremented every state time (osc/2) or asynchronously from pin T2;

under these conditions, a read or write of TH2 or TL2 may not be

accurate. The RCAP2 registers may be read, but should not be

written to, because a write might overlap a reload and cause write

and/or reload errors. The timer should be turned off (clear TR2)

before accessing the Timer 2 or RCAP2 registers.

Table 3 shows commonly used baud rates and how they can be

obtained from Timer 2.

Summary Of Baud Rate Equations

Timer 2 is in baud rate generating mode. If Timer 2 is being clocked

through pin T2(P1.0) the baud rate is:

Baud Rate

+ Timer 2 Overflow Rate

If Timer 2 is being clocked internally, the baud rate is:

Baud Rate

OSC

[32

[65536

* (RCAP2H, RCAP2L)]]

Where fOSC= Oscillator Frequency

To obtain the reload value for RCAP2H and RCAP2L, the above

equation can be rewritten as:

RCAP2H, RCAP2L

+ 65536 *

OSC

Baud Rate

Timer/Counter 2 Set-up

Except for the baud rate generator mode, the values given for

T2CON do not include the setting of the TR2 bit. Therefore, bit TR2

must be set, separately, to turn the timer on. see Table 4 for set-up

of Timer 2 as a timer. Also see Table 5 for set-up of Timer 2 as a

counter.

POWER OFF FLAG3

The Power Off Flag (POF) is set by on-chip circuitry when the VCC

level on the 80C54/80C58 rises from 0 to 5V. The POF bit can be

set or cleared by software allowing a user to determine if the reset is

the result of a power-on or a warm start after powerdown. The VCC

level must remain above 3V for the POF to remain unaffected by the

VCC level.

Table 4. Timer 2 as a Timer

MODE

T2CON

MODE

INTERNAL CONTROL

(Note 1)

EXTERNAL CONTROL

(Note 2)

16-bit Auto-Reload

00H

08H

16-bit Capture

01H

09H

Baud rate generator receive and transmit same baud rate

34H

36H

Receive only

24H

26H

Transmit only

14H

16H

Table 5. Timer 2 as a Counter

MODE

TMOD

MODE

INTERNAL CONTROL

(Note 1)

EXTERNAL CONTROL

(Note 2)

16-bit

02H

0AH

Auto-Reload

03H

0BH

NOTES:

1. Capture/reload occurs only on timer/counter overflow.

2. Capture/reload occurs on timer/counter overflow and a 1-to-0 transition on T2EX (P1.1) pin except when Timer 2 is used in the baud rate

generator mode.

3. POF not present in 80C52.

80C32EBAA 数据表(PDF) 42 Page - NXP Semiconductors

80C32EBAA 数据表(HTML) 42 Page - NXP Semiconductors

Html Pages

1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 41 42 43 44 45 46 47 48 49 50 51 52 53 54 55 56 57 58 59 60 61 62

数据表下载

链接网址

80C32EBAA 数据表(PDF) 42 Page - NXP Semiconductors

80C32EBAA 数据表(HTML) 42 Page - NXP Semiconductors

Html Pages

1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 41 42 43 44 45 46 47 48 49 50 51 52 53 54 55 56 57 58 59 60 61 62

数据表 下载

链接网址

数据表下载