MPXM2102AS datasheet(93/670 Pages) MOTOROLA

93 / 670 page

MMA3201D

2–57

Motorola Sensor Device Data

www.motorola.com/semiconductors

OPERATING CHARACTERISTICS

(Unless otherwise noted: –40

°C v TA v +85°C, 4.75 v VDD v 5.25, X and Y Channels, Acceleration = 0g, Loaded output(1))

Characteristic

Symbol

Min

Typ

Max

Unit

Operating Range(2)

Supply Voltage(3)

Supply Current

Operating Temperature Range

Acceleration Range

VDD

IDD

gFS

4.75

*40

—

5.00

—

5.25

+85

—

°C

Output Signal

Zero g (VDD = 5.0 V)(4)

Zero g

Sensitivity (TA = 25°C, VDD = 5.0 V)(5)

Sensitivity

Bandwidth Response

Nonlinearity

VOFF

VOFF,V

f –3dB

NLOUT

2.2

0.44 VDD

360

*1.0

2.5

0.50VDD

400

—

2.8

0.56 VDD

440

+1.0

mV/g

mV/g/V

% FSO

Noise

RMS (.01–1 kHz)

Power Spectral Density

Clock Noise (without RC load on output)(6)

nRMS

nPSD

nCLK

—

110

2.0

2.8

—

mVrms

µV/(Hz1/2)

mVpk

Self–Test

Output Response

Input Low

Input High

Input Loading(7)

Response Time(8)

gST

VIL

VIH

IIN

tST

9.6

VSS

0.7 x VDD

*30

—

*110

2.0

14.4

0.3 x VDD

VDD

*300

—

µA

Status(12)(13)

Output Low (Iload = 100 µA)

Output High (Iload = 100 µA)

VOL

VOH

—

VDD *.8

—

0.4

—

Minimum Supply Voltage (LVD Trip)

VLVD

2.7

3.25

4.0

Clock Monitor Fail Detection Frequency

fmin

—

260

kHz

Output Stage Performance

Electrical Saturation Recovery Time(9)

Full Scale Output Range (IOUT = 200 µA)

Capacitive Load Drive(10)

Output Impedance

tDELAY

VFSO

—

0.3

—

0.2

—

300

—

VDD *0.3

100

—

Ω

Mechanical Characteristics

Transverse Sensitivity(11)

Package Resonance

VZX,YX

fPKG

—

5.0

—

% FSO

kHz

NOTES:

1. For a loaded output the measurements are observed after an RC filter consisting of a 1 k

Ω resistor and a 0.01 µF capacitor to ground.

2. These limits define the range of operation for which the part will meet specification.

3. Within the supply range of 4.75 and 5.25 volts, the device operates as a fully calibrated linear accelerometer. Beyond these supply limits

the device may operate as a linear device but is not guaranteed to be in calibration.

4. The device can measure both + and

* acceleration. With no input acceleration the output is at midsupply. For positive acceleration the output

will increase above VDD/2 and for negative acceleration the output will decrease below VDD/2.

5. The device is calibrated at 20g.

6. At clock frequency

^ 70 kHz.

7. The digital input pin has an internal pull–down current source to prevent inadvertent self test initiation due to external board level leakages.

8. Time for the output to reach 90% of its final value after a self–test is initiated.

9. Time for amplifiers to recover after an acceleration signal causing them to saturate.

10. Preserves phase margin (60

°) to guarantee output amplifier stability.

11. A measure of the device’s ability to reject an acceleration applied 90

° from the true axis of sensitivity.

12. The Status pin output is not valid following power–up until at least one rising edge has been applied to the self–test pin. The Status pin is

high whenever the self–test input is high.

13. The Status pin output latches high if a Low Voltage Detection or Clock Frequency failure occurs, or the EPROM parity changes to odd. The

Status pin can be reset by a rising edge on self–test, unless a fault condition continues to exist.

Freescale Semiconductor, Inc.

For More Information On This Product,

Go to: www.freescale.com

MPXM2102AS 数据表(PDF) 93 Page - Motorola, Inc

MPXM2102AS 数据表(HTML) 93 Page - Motorola, Inc

Html Pages

1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 41 42 43 44 45 46 47 48 49 50 51 52 53 54 55 56 57 58 59 60 61 62 63 64 65 66 67 68 69 70 71 72 73 74 75 76 77 78 79 80 81 82 83 84 85 86 87 88 89 90 91 92 93 94 95 96 97 98 99 100 ...More

数据表下载