LPC47M14X datasheet(21/205 Pages) SMSC

21 / 205 page

SMSC DS – LPC47M14X

Page 21

Rev. 03/19/2001

6.3

LPC INTERFACE

The following sub-sections specify the implementation of the LPC bus.

6.3.1

LPC Interface Signal Definition

The signals required for the LPC bus interface are described in the table below. LPC bus signals use PCI 33MHz

electrical signal characteristics.

SIGNAL

NAME

TYPE

DESCRIPTION

LAD[3:0]

I/O

LPC address/data bus. Multiplexed command, address and data bus.

LFRAME#

Input

Frame signal. Indicates start of new cycle and termination of broken cycle

PCI_RESET#

Input

PCI Reset. Used as LPC Interface Reset.

LDRQ#

Output

Encoded DMA/Bus Master request for the LPC interface.

nIO_PME

Power Mgt Event signal. Allows the LPC47M14x to request wakeup.

LPCPD#

Input

Powerdown Signal. Indicates that the LPC47M14x should prepare for power to be shut

on the LPC interface.

SER_IRQ

I/O

Serial IRQ.

PCI_CLK

Input

PCI Clock.

Note: The CLKRUN# signal is not implemented in this part.

6.3.2

LPC Cycles

The following cycle types are supported by the LPC protocol.

CYCLE TYPE

TRANSFER SIZE

I/O Write

1 Byte

I/O Read

1 Byte

DMA Write

1 byte

DMA Read

1 byte

The LPC47M14x ignores cycles that it does not support.

6.3.3

Field Definitions

The data transfers are based on specific fields that are used in various combinations, depending on the cycle type.

These fields are driven onto the LAD[3:0] signal lines to communicate address, control and data information over the

LPC bus between the host and the LPC47M14x. See the “Low Pin Count (LPC) Interface Specification”, Revision

1.0, Section 4.2 for definition of these fields.

6.3.4

LFRAME# Usage

LFRAME# is used by the host to indicate the start of cycles and the termination of cycles due to an abort or time-out

condition. This signal is to be used by the LPC47M14x to know when to monitor the bus for a cycle.

This signal is used as a general notification that the LAD[3:0] lines contain information relative to the start or stop of a

cycle, and that the LPC47M14x monitors the bus to determine whether the cycle is intended for it. The use of

LFRAME# allows the LPC47M14x to enter a lower power state internally. There is no need for the LPC47M14x to

monitor the bus when it is inactive, so it can decouple its state machines from the bus, and internally gate its clocks.

When the LPC47M14x samples LFRAME# active, it immediately stops driving the LAD[3:0] signal lines on the next

clock and monitor the bus for new cycle information.

The LFRAME# signal functions as described in the Low Pin Count (LPC) Interface Specification, Revision 1.0.

LPC47M14X 数据表(PDF) 21 Page - SMSC Corporation

LPC47M14X 数据表(HTML) 21 Page - SMSC Corporation

Html Pages

1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 41 42 43 44 45 46 47 48 49 50 51 52 53 54 55 56 57 58 59 60 61 62 63 64 65 66 67 68 69 70 71 72 73 74 75 76 77 78 79 80 81 82 83 84 85 86 87 88 89 90 91 92 93 94 95 96 97 98 99 100 ...More

数据表下载

链接网址

LPC47M14X 数据表(PDF) 21 Page - SMSC Corporation

LPC47M14X 数据表(HTML) 21 Page - SMSC Corporation

Html Pages

1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 41 42 43 44 45 46 47 48 49 50 51 52 53 54 55 56 57 58 59 60 61 62 63 64 65 66 67 68 69 70 71 72 73 74 75 76 77 78 79 80 81 82 83 84 85 86 87 88 89 90 91 92 93 94 95 96 97 98 99 100 ...More

数据表 下载

链接网址

数据表下载