AD9983ASLASHPCB datasheet(39/44 Pages) AD

39 / 44 page

Preliminary Technical Data

AD9983A

Rev. PrA | Page 39 of 44

0x2C—Bits[7:5] Auto-Offset Hold

Must be written to 0x00 for proper operation.

0x2C—Bit[4] Auto-Offset Hold

A bit for controlling whether the auto-offset function runs

continuously or runs once and holds the result. Continuous

updates are recommended because this allows the AD9983A to

compensate for drift over time and temperature. If one-time

updates are preferred, these should be performed every time the

part is powered up and when there is a mode change. To do a

one-time update, first auto-offset must be enabled (Register

0x1B, Bit 5). Next, this bit (auto-offset hold) must first be set to

1 to let the auto-offset function operate and settle to a final

value. Auto-offset hold should then be set to 0 to hold the offset

values that the auto circuitry calculates. The AD9983A auto-

offset circuit’s maximum settle time is 10 updates. For example,

if the update frequency is set to once every 64 Hsyncs, then the

maximum settling time would be 640 Hsyncs (10 × 64 Hsyncs).

Table 77. Auto-Offset Hold

Select

Result

Disables auto-offset updates and holds the

current auto-offset values

Allows auto-offset to update continuously

0x2C—Bits[3:0]

Must be written to 0x0 for proper operation.

0x2D—Bits[7:0] Test Register 5

Read/write bits for future use. Must be written to 0xE8 for

proper operation.

0x2E—Bits[7:0] Test Register 6

Read/write bits for future use. Must be written to 0xE0 for

proper operation.

0x34—Bit[2] SOG Filter Enable

This bit enables the SOG filter, which will reject inputs with a

width of less than 250 ns. This aids the PLL in the ability to

ignore extraneous (non-valid) sync pulses.

Table 78. SOG Filter Enable

Select

Result

SOG filter disabled

SOG filter enabled

0x36—Bit[0] VCO Gear Select

This bit allows the VCO to select a lower ‘gear’ which enables it

to run lower pixel clocks while remaining in a more linear range.

Table 79. VCO Gear Select

Select

Result

Normal VCO setting

Enables lower VCO clock output

0x3C—Bits[7:4] Test Bits

Must be set to 0x0 for proper operation.

0x3C—Bit[3] Auto Gain Matching Hold

A bit for controlling whether the auto gain matching function

runs continuously or runs once and holds the result.

Continuous updates are recommended because it allows the

AD9983A to compensate for drift over time and temperature.

If one-time updates are preferred, these should be performed

every time the part is powered up and when there is a mode

change. To do a one-time update, first auto gain matching must

be enabled (Register Ox3C, Bit 2). Next, this bit (Auto Gain

Matching Hold) must first be set to 1 to let the auto gain

matching function operate and settle to a final value. The Auto

Gain Matching Hold bit should then be set to 0 to hold the gain

values that the auto circuitry calculates. The AD9983A auto gain

matching circuit’s maximum settle time is 10 updates. For example,

if the update frequency is set to once every 64 Hsyncs, then the

maximum settling time would be 640 Hsyncs (10 x 64 Hsyncs).

Table 80. Auto Gain Hold

Select

Result

Disables auto gain updates and holds the

current auto offset values

Allows auto gain to update continuously

The power-up default setting is 0.

0x3C—Bits[2:0] Auto Gain Matching Enable

These bits enable or disable the auto gain matching function.

When set to 000, the auto gain matching function is disabled;

when set to 110 the auto gain matching function is enabled.

Table 81. Auto Gain Matching Enable

Select

Result

000

Auto gain matching disabled

110

Auto gain matching enabled

AD9983A/PCB 数据表(PDF) 39 Page - Analog Devices

AD9983A/PCB 数据表(HTML) 39 Page - Analog Devices

Html Pages

1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 41 42 43 44

数据表下载

链接网址

AD9983A/PCB 数据表(PDF) 39 Page - Analog Devices

AD9983A/PCB 数据表(HTML) 39 Page - Analog Devices

Html Pages

1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 41 42 43 44

数据表 下载

链接网址

数据表下载