| 数据搜索系统,热门电子元器件搜索 |
|
PPC405EP 数据表(PDF) 32 Page - Applied Micro Circuits Corporation |
|
|
|||||||||||||||||||||||||||||
PPC405EP 数据表(HTML) 32 Page - Applied Micro Circuits Corporation |
|
32 / 50 page ![]() PPC405EP – PowerPC 405EP Embedded Processor 32 AMCC Revision 1.07 – September 10, 2007 Data Sheet PCIReq1:2 PCIReq input when internal arbiter is used. I 5V tolerant 3.3V PCI PCIGnt0/Req Gnt0 when internal arbiter is used or Req when external arbiter is used. O 5V tolerant 3.3V PCI PCIGnt1:2 PCIGnt output when internal arbiter is used. O 5V tolerant 3.3V PCI Ethernet Interface PHY0Rx0:1D3:0 Received data. This is a nibble wide bus from the PHY. The data is synchronous with the PHY0RxClk. I 5V tolerant 3.3V LVTTL 1 EMC0Tx0:1D3:0 Transmit data. A nibble wide data bus towards the net. The data is synchronous to the PHY0TxClk. O 5V tolerant 3.3V LVTTL PHY0Rx0:1Err Receive Error. This signal comes from the PHY and is synchronous to the PHY0RxClk. I 5V tolerant 3.3V LVTTL 1 PHY0Rx0:1Clk Receive Medium clock. This signal is generated by the PHY. If an EMAC interface is not used, this clock must be present in order to reset the EMAC. I 5V tolerant 3.3V LVTTL 1 PHY0Rx0:1DV Receive Data Valid. Data on the Data Bus is valid when this signal is activated. Deassertion of this signal indicates end of the frame reception. I 5V tolerant 3.3V LVTTL 1 PHY0CrS0:1 Carrier Sense signal from the PHY. This is an asynchronous signal. I 5V tolerant 3.3V LVTTL 1 EMC0Tx0:1Err Transmit Error. This signal is generated by the Ethernet controller, is connected to the PHY and is synchronous with the PHYTxClk. It informs the PHY that an error was detected. O 5V tolerant 3.3V LVTTL EMC0Tx0:1En Transmit Enable. This signal is driven by the EMAC to the PHY. Data is valid during the active state of this signal. Deassertion of this signal indicates end of frame transmission. This signal is synchronous to the PHY0TxClk. O 5V tolerant 3.3V LVTTL PHY0Tx0:1Clk This clock comes from the PHY and is the Medium Transmit clock. If an EMAC interface is not used, this clock must be present in order to reset the EMAC. I 5V tolerant 3.3V LVTTL 1 PHY0Col0:1 Collision signal from the PHY. This is an asynchronous signal. I 5V tolerant 3.3V LVTTL 1 EMC0MDClk Management Data Clock. The MDClk is sourced to the PHY. Management information is transferred synchronously with respect to this clock. O 5V tolerant 3.3V LVTTL EMC0MDIO Management Data Input/Output is a bidirectional signal between the Ethernet controller and the PHY. It is used to transfer control and status information. I/O 5V tolerant 3.3V LVTTL 1 Table 6. Signal Functional Description (Sheet 2 of 6) Secondary multiplexed signals are shown in brackets. Notes: 1. Receiver input has hysteresis. 2. Must pull up. See “Pull-Up and Pull-Down Resistors” on page 29 for recommended termination values. 3. Must pull down. See “Pull-Up and Pull-Down Resistors” on page 29 for recommended termination values. 4. If not used, must pull up. 5. If not used, must pull down. 6. Strapping input during reset; pull up or pull down as required. 7. Pull-up may be required. See “External Bus Control Signals” on page 30. Signal Name Description I/O Type Notes |
|
链接网址 |
| ALLDATASHEET是否为您带来帮助? [ DONATE ] |
关于 Alldatasheet | 广告服务 | 联系我们 | 隐私政策 | 数据表链接 | 链接交换 | 制造商名单 All Rights Reserved©Alldatasheet.com |
| Russian : Alldatasheetru.com | Korean : Alldatasheet.co.kr | Spanish : Alldatasheet.es | French : Alldatasheet.fr | Italian : Alldatasheetit.com Portuguese : Alldatasheetpt.com | Polish : Alldatasheet.pl | Vietnamese : Alldatasheet.vn Indian : Alldatasheet.in | Mexican : Alldatasheet.com.mx | British : Alldatasheet.co.uk | New Zealand : Alldatasheet.co.nz |
|
Family Site : ic2ic.com |
icmetro.com |