| 数据搜索系统,热门电子元器件搜索 |
|
PPC440EP 数据表(PDF) 56 Page - Applied Micro Circuits Corporation |
|
|
|||||||||||||||||||||||||||||
PPC440EP 数据表(HTML) 56 Page - Applied Micro Circuits Corporation |
|
56 / 84 page ![]() 56 AMCC Proprietary 440EP – PPC440EP Embedded Processor Revision 1.26 – April 25, 2007 Data Sheet NAND Flash Interface NFALE Address Latch Enable. O Multiplex NFCE0:3 Chip Enable (multiplexed with the PerCS0:3 signals). O Multiplex NFCLE Command Latch Enable. O Multiplex NFRdyBusy Ready/Busy. Indicates status of device during program erase or page read. This signal is wire-or connected from all NAND Flash devices. I Multiplex NFREn Read Enable strobe. O Multiplex NFWEn Write Enable strobe. O Multiplex Serial Peripheral Interface SCPClkOut Clock output. SCPClkOut, the serial port master clock out, is used to synchronize all data movement both into and out of the device through the serial data ports. Normally, data is shifted out on the rising edge of the clock and shifted in on the negative edge. SCPClkOut is also used to shift data into and out of the slave device. When the SPMODE register is reset, SCPClkOut is forced to 0. O3.3V LVTTL SCPDI Data In. Data is received from the connected slave device and is captured synchronously with SysClk. I3.3V LVTTL SCPDO Data output. Data is sent to the connected slave device synchronously with SysClk. O3.3V LVTTL Interrupts Interface IRQ0:4 External interrupt requests 0 through 4. I/O 3.3V LVTTL 1, 5 IRQ5 External interrupt request 5. I 3.3V tolerant 2.5V CMOS 1 IRQ6:9 External interrupt requests 6 through 9. I/O 3.3V LVTTL 1 JTAG Interface TCK Test Clock. I 3.3V LVTTL w/pull-up 1 TDI Test Data In. I 3.3V LVTTL w/pull-up 4 TDO Test Data Out. O 3.3V LVTTL TMS Test Mode Select. I 3.3V LVTTL w/pull-up 1 TRST Test Reset. I 3.3V LVTTL w/pull-up 5 Table 6. Signal Functional Description (Sheet 7 of 9) Notes: 1. Receiver input has hysteresis 2. Must pull up (recommended value is 3k Ω to 3.3V) 3. Must pull down (recommended value is 1k Ω) 4. If not used, must pull up (recommended value is 3k Ω to 3.3V) 5. If not used, must pull down (recommended value is 1k Ω) 6. Strapping input during reset; pull-up or pull-down required Signal Name Description I/O Type Notes |
|
链接网址 |
| ALLDATASHEET是否为您带来帮助? [ DONATE ] |
关于 Alldatasheet | 广告服务 | 联系我们 | 隐私政策 | 数据表链接 | 链接交换 | 制造商名单 All Rights Reserved©Alldatasheet.com |
| Russian : Alldatasheetru.com | Korean : Alldatasheet.co.kr | Spanish : Alldatasheet.es | French : Alldatasheet.fr | Italian : Alldatasheetit.com Portuguese : Alldatasheetpt.com | Polish : Alldatasheet.pl | Vietnamese : Alldatasheet.vn Indian : Alldatasheet.in | Mexican : Alldatasheet.com.mx | British : Alldatasheet.co.uk | New Zealand : Alldatasheet.co.nz |
|
Family Site : ic2ic.com |
icmetro.com |