PIC16F1507-ESLASHSS. datasheet(115/278 Pages) MICROCHIP

115 / 278 page

 2011-2015 Microchip Technology Inc.

DS40001586D-page 115

PIC16(L)F1507

14.0

TEMPERATURE INDICATOR

MODULE

This family of devices is equipped with a temperature

circuit designed to measure the operating temperature

of the silicon die. The circuit’s range of operating

temperature falls between -40°C and +85°C. The

output is a voltage that is proportional to the device

temperature. The output of the temperature indicator is

internally connected to the device ADC.

The circuit may be used as a temperature threshold

detector or a more accurate temperature indicator,

depending on the level of calibration performed. A one-

point calibration allows the circuit to indicate a

temperature closely surrounding that point. A two-point

calibration allows the circuit to sense the entire range

of temperature more accurately. Reference Application

Note AN1333, “Use and Calibration of the Internal

Temperature Indicator

” (DS01333) for more details

regarding the calibration process.

14.1

Circuit Operation

Figure 14-1 shows a simplified block diagram of the

temperature circuit. The proportional voltage output is

achieved by measuring the forward voltage drop across

multiple silicon junctions.

Equation 14-1 describes the output characteristics of

the temperature indicator.

EQUATION 14-1:

VOUT RANGES

The temperature sense circuit is integrated with the

Fixed Voltage Reference (FVR) module. See Section

13.0 “Fixed Voltage Reference (FVR)”

for more

information.

The circuit is enabled by setting the TSEN bit of the

FVRCON register. When disabled, the circuit draws no

current.

The circuit operates in either high or low range. The high

range, selected by setting the TSRNG bit of the

FVRCON register, provides a wider output voltage. This

provides more resolution over the temperature range,

but may be less consistent from part to part. This range

requires a higher bias voltage to operate and thus, a

higher VDD is needed.

The low range is selected by clearing the TSRNG bit of

the FVRCON register. The low range generates a lower

voltage drop and thus, a lower bias voltage is needed to

operate the circuit. The low range is provided for low

voltage operation.

FIGURE 14-1:

TEMPERATURE CIRCUIT

DIAGRAM

14.2

Minimum Operating VDD

When the temperature circuit is operated in low range,

the device may be operated at any operating voltage

that is within specifications.

When the temperature circuit is operated in high range,

the device operating voltage, VDD, must be high

enough to ensure that the temperature circuit is

correctly biased.

Table 14-1 shows the recommended minimum VDD vs.

range setting.

TABLE 14-1:

RECOMMENDED VDD VS.

RANGE

14.3

Temperature Output

The output of the circuit is measured using the internal

Analog-to-Digital Converter. A channel is reserved for

the temperature circuit output. Refer to Section

15.0 “Analog-to-Digital Converter (ADC) Module”

for

detailed information.

14.4

ADC Acquisition Time

To ensure accurate temperature measurements, the

user must wait at least 200

s after the ADC input

multiplexer is connected to the temperature indicator

output before the conversion is performed. In addition,

the user must wait 200

s between sequential

conversions of the temperature indicator output.

High Range: VOUT = VDD - 4VT

Low Range: VOUT = VDD - 2VT

Min. VDD, TSRNG = 1

Min. VDD, TSRNG = 0

3.6V

1.8V

VOUT

Temp. Indicator

To ADC

TSRNG

TSEN

Rev. 10-000069A

7/31/2013

VDD

PIC16F1507-E/SS. 数据表(PDF) 115 Page - Microchip Technology

PIC16F1507-E/SS. 数据表(HTML) 115 Page - Microchip Technology

Html Pages

1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 41 42 43 44 45 46 47 48 49 50 51 52 53 54 55 56 57 58 59 60 61 62 63 64 65 66 67 68 69 70 71 72 73 74 75 76 77 78 79 80 81 82 83 84 85 86 87 88 89 90 91 92 93 94 95 96 97 98 99 100 ...More

数据表下载