ST6369 datasheet(20/71 Pages) STMICROELECTRONICS

20 / 71 page

The interrupt vector associated with the non-mask-

able interrupt source is named interrupt vector #0.

It is located at the (FFCH,FFDH) addresses in the

Program Space. This vector is associated with the

PC6/IRIN pin.

The interrupt vectors located at addresses

(FF6H,FF7H),

(FF4H,FF5H),

(FF2H,FF3H),

(FF0H,FF1H) are named interrupt vectors #1, #2,

#3 and #4 respectively. These vectors are associ-

ated with TIMER 2 (#1), VSYNC (#2), TIMER 1

(#3) and PC4(PWRIN) (#4).

Interrupt Priority

The non-maskable interrupt request has the high-

est priority and can interrupt any other interrupt

routines at any time, nevertheless the other inter-

rupts cannot interrupt each other. If more than one

interrupt request is pending, they are processed by

the ST6369 Core according to their priority level:

vector #1 has the higher priority while vector #4 the

lower. The priority of each interrupt source is hard-

ware fixed.

Interrupt Option Register

The Interrupt Option Register (IOR register, loca-

tion C8H) is used to enable/disable the individual

interrupt sources and to select the operating mode

of the external interrupt inputs. This register can be

addressed in the Data Space as RAM location at

the C8H address, nevertheless it is write-only reg-

ister that can not be accessed with single-bit op-

erations. The operating modes of the external

interrupt inputs associated to interrupt vectors #1

and #2 are selected through bits 4 and 5 of the IOR

D7. Not used.

EL1. This is the Edge/Level selection bit of inter-

rupt #1. When set to one, the interrupt is generated

on low level of the related signal; when cleared to

zero, the interrupt is generated on falling edge. The

bit is cleared to zero after reset.

ES2. This is the edge selection bit on interrupt #2.

This bit is used on the ST6369 devices with on-chip

OSD generator for VSYNC detection.

GEN. This is the global enable bit. When set to one all

interrupts are globally enabled; when this bit is cleared

to zero all interrupts are disabled (excluding NMI).

D3 - D0. These bits are not used.

Interrupt Source

Associated

Vector

Vector Address

PC6/IRIN

Pin (1)

Interrupt

Vector # 0 (NMI)

0FFCH-0FFDH

Timer 2

Interrupt

Vector # 1

0FF6H-0FF7H

Vsync

Interrupt

Vector # 2

0FF4H-0FF5H

Timer 1

Interrupt

Vector # 3

0FF2H-0FF3H

PC4/PWRIN

Interrupt

Vector # 4

0FF0H-0FF1H

Note: 1. This pin is associated with the NMI Interrupt Vector

Table 6. Interrupt Vectors/Sources

Relationships

INTERRUPT (Continued)

IOR

Interr upt Option Register

(C8H, Write Only)

D7 D6 D5 D4 D3 D2 D1 D0

Unuse d

GEN = Global Enab le Bit

ES2 = Edge Selection Bit

EL1 = Edge Level Selection Bit

Unuse d

GEN = Global Enab le Bit

ES2 = Edge Selection Bit

EL1 = Edge Level Selection Bit

Unuse d

Figure 18. Interrupt Option Register

ST6369

16/67

ST6369 数据表(PDF) 20 Page - STMicroelectronics

ST6369 数据表(HTML) 20 Page - STMicroelectronics

Html Pages

1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 41 42 43 44 45 46 47 48 49 50 51 52 53 54 55 56 57 58 59 60 61 62 63 64 65 66 67 68 69 70 71

数据表下载

链接网址

ST6369 数据表(PDF) 20 Page - STMicroelectronics

ST6369 数据表(HTML) 20 Page - STMicroelectronics

Html Pages

1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 41 42 43 44 45 46 47 48 49 50 51 52 53 54 55 56 57 58 59 60 61 62 63 64 65 66 67 68 69 70 71

数据表 下载

链接网址

数据表下载