ADE7166 datasheet(78/148 Pages) AD

78 / 148 page

ADE75xx/ADE71xx

Preliminary Technical Data

Rev. PrE | Page 78 of 148

by the assembler and stored in the memory address specified.

This number is referred to as a literal because it refers only to a

value and not to a memory location. Instructions using this

addressing mode will be slower than those between two

registers since the literal must be stored and fetched from

memory. The expression can be entered as a symbolic variable

or an arithmetic expression; the value will be computed by the

assembler.

Direct Addressing:

With Direct Addressing, the value at the

source address is moved to the destination address. Direct

Addressing provides the fastest execution time of all the

addressing modes when an instruction is performed between

registers using direct addressing. Note that indirect or direct

addressing modes can be used to access general purpose RAM

addresses 0x00 through 0x7F. An instruction with direct

addressing that uses an address between 0x80 and 0xFF is

referring to a special function memory location.

Indirect Addressing:

With Indirect Addressing, the value

pointed to by the register is moved to the destination address.

For example, to move the contents of internal RAM address 82h

to the accumulator:

MOV

R0,#82h

MOV

A,@R0

The two instructions above require a total of four clock cycles

and three bytes of storage in the program memory.

Indirect addressing allows addresses to be computed, and is

useful for indexing into data arrays stored in RAM.

Note that an instruction that refers to addresses 00 through 7Fh

is referring to internal RAM and indirect or direct addressing

modes can be used. An instruction with indirect addressing that

uses an address between 80h and FFh is referring to internal

RAM, not to a SFR.

Extended Direct Addressing:

The DPTR register is used to

access internal extended RAM in extended indirect addressing

mode. The ADE75XX/ADE71XX provides 256 bytes of internal

extended RAM (XRAM), accessed through MOVX instructions.

External memory spaces are not supported on this device.

In extended direct addressing mode, the DPTR register points

to the address of the byte of extended RAM. The following code

will move the contents of extended RAM address 100h to the

accumulator:

MOV

DPTR,#100h

MOVX A,@DPTR

The two instructions above require a total of seven clock cycles

and four bytes of storage in the program memory.

Extended Indirect Addressing:

The internal extended RAM is

accessed through a pointer to the address in indirect addressing

mode. The ADE75XX/ADE71XX provides 256 bytes of internal

extended RAM, accessed through MOVX instructions. External

memory is not supported on this device.

In extended indirect addressing mode, a register holds the

address of the byte of extended RAM. The following code will

move the contents of extended RAM address 80h to the

accumulator:

MOV

R0,#80h

MOVX A,@R0

The two instructions above require six clock cycles and three

bytes of storage.

Note that there are 256 bytes of extended RAM, so both

extended direct and extended indirect addressing can cover the

whole address range. There is a storage and speed advantage to

using extended indirect addressing because the additional byte

of addressing available through the DPTR register that is not

needed is not stored.

From the three examples demonstrating the access of internal

RAM from 80h through FFh and extended internal RAM from

00h through FFh, it can be seen that it is most efficient to use

the entire internal RAM accessible through indirect access

before moving to extended RAM.

Code Indirect Addressing:

The internal code memory can be

accessed indirectly. This can be useful for implementing lookup

tables and other arrays of constants that are stored in Flash. For

example, to move the data stored in Flash memory at address

8002h into the Accumulator:

MOV

DPTR,#8002h

CLR

MOVX A,@A+DPTR

The Accumulator can be used as a variable index into the array

of Flash memory located at DPTR.

INSTRUCTION SET

Table 61 documents the number of clock cycles required for

eachinstruction. Most instructions are executed in one or two

clock cycles,resulting in a 4 MIPS peak performance.

Table 61. Instruction Set

Mnemonic

Description

Bytes

Cycles

Arithmetic

ADD A,Rn

Add register to A

ADD A,@Ri

Add indirect memory to A

ADE7166 数据表(PDF) 78 Page - Analog Devices

ADE7166 数据表(HTML) 78 Page - Analog Devices

Html Pages

1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 41 42 43 44 45 46 47 48 49 50 51 52 53 54 55 56 57 58 59 60 61 62 63 64 65 66 67 68 69 70 71 72 73 74 75 76 77 78 79 80 81 82 83 84 85 86 87 88 89 90 91 92 93 94 95 96 97 98 99 100 ...More

数据表下载