PSD913F2 datasheet(16/91 Pages) STMICROELECTRONICS

16 / 91 page

PSD935G2

PSD9XX Family

9.0

The

PSD935G2

Functional

Blocks

As shown in Figure 1, the PSD935G2 consists of six major types of functional blocks:

t Memory Blocks

t PLD Blocks

t Bus Interface

t I/O Ports

t Power Management Unit

t JTAG-ISP Interface

The functions of each block are described in the following sections. Many of the blocks

perform multiple functions, and are user configurable.

9.1 Memory Blocks

The PSD935G2 has the following memory blocks:

• The main Flash memory

• Secondary Flash memory

• SRAM.

The memory select signals for these blocks originate from the Decode PLD (DPLD) and

are user-defined in PSDsoft.

Table 7 summarizes which versions of the PSD935G2 contain which memory blocks.

Main Flash

Secondary Flash

Device

Flash Size

Sector Size

Block Size

Sector Size

SRAM

PSD935G2

512KB

64KB

32KB

8KB

Table 7. Memory Blocks

9.1.1 Main Flash and Secondary Flash Memory Description

The main Flash memory block is divided evenly into eight sectors. The secondary Flash

memory is divided into four sectors of eight Kbytes each. Each sector of either memory

can be separately protected from program and erase operations.

Flash memory may be erased on a sector-by-sector basis and programmed word-by-word.

Flash sector erasure may be suspended while data is read from other sectors of memory

and then resumed after reading.

During a program or erase of Flash, the status can be output on the Rdy/Bsy pin of Port

PE4. This pin is set up using PSDsoft.

9.1.1.1 Memory Block Selects

The decode PLD in the PSD935G2 generates the chip selects for all the internal memory

blocks (refer to the PLD section). Each of the eight Flash memory sectors have a

Flash Select signal (FS0-FS7) which can contain up to three product terms. Each of the

four Secondary Flash memory sectors have a Select signal (CSBOOT0-3) which can

contain up to three product terms. Having three product terms for each sector select signal

allows a given sector to be mapped in different areas of system memory. When using a

microcontroller (80C51) with separate Program and Data space, these flexible select

signals allow dynamic re-mapping of sectors from one space to the other before and after

IAP.

PSD913F2 数据表(PDF) 16 Page - STMicroelectronics

PSD913F2 数据表(HTML) 16 Page - STMicroelectronics

Html Pages

1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 41 42 43 44 45 46 47 48 49 50 51 52 53 54 55 56 57 58 59 60 61 62 63 64 65 66 67 68 69 70 71 72 73 74 75 76 77 78 79 80 81 82 83 84 85 86 87 88 89 90 91

数据表下载

链接网址

PSD913F2 数据表(PDF) 16 Page - STMicroelectronics

PSD913F2 数据表(HTML) 16 Page - STMicroelectronics

Html Pages

1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 41 42 43 44 45 46 47 48 49 50 51 52 53 54 55 56 57 58 59 60 61 62 63 64 65 66 67 68 69 70 71 72 73 74 75 76 77 78 79 80 81 82 83 84 85 86 87 88 89 90 91

数据表 下载

链接网址

数据表下载