CS49310 datasheet(40/90 Pages) CIRRUS

40 / 90 page

CS49300 Family DSP

DS339F7

preceding any write. The 0x00 byte represents

the 7 bit of address (0000000b) and the

read/write bit set to 0 to designate a write.

3) After each byte (including the address and

each data byte) the host must release the data

line and provide a ninth clock for the CS493XX

to acknowledge. The CS493XX will drive the

data line low during the ninth clock to

acknowledge. If for some reason the CS493XX

does not acknowledge, it means that the last

byte sent was not received and should be

resent. If the resent byte fails to produce an

acknowledge, a stop condition should be sent

and the device should be reset.

4) The host should then clock data into the device

most significant bit first, one byte at a time. The

CS493XX will (and must) acknowledge each

byte that it receives which means that after

each

byte

the

host

must

provide

acknowledge clock pulse on SCCLK and

release the data line, SCDIO.

5) At the end of a data transfer a stop condition

must be sent. The stop condition is defined as

the rising edge of SCDIO while SCCLK is high.

6.1.2.2. Reading in I2C®

A read operation is necessary when the CS493XX

signals that it has data to be read. It does this by

dropping its interrupt request line (INTREQ) low.

When reading from the device in I2C®, the same

protocol will be used whether reading a single byte

or multiple bytes. The examples shown in this

document can be expanded to fit any read

situation. Figure 23 shows a typical I2C® read

sequence

1) An I2C® read transaction is initiated by the

CS493XX dropping INTREQ, signaling that it

has data to be read.

2) The host responds by sending an I2C® start

condition which is SCDIO dropping while

SCCLK is held high.

3) The start condition is followed by a 7-bit

address and the read/write bit set high for a

read. The address for the CS493XX defaults to

0000000b. It is necessary to clock this address

in prior to any transfer in order for the

CS493XX to acknowledge the read. In other

words a byte of 0x01 should be clocked into the

device preceding any read. The 0x01 byte

represents the 7 bit address 0000000b and a

read/write bit set to 1 to designate a read.

4) After the falling edge of the serial control clock

(SCCLK) for the read/write bit of the address

byte, an acknowledge must be read in by the

host. The CS493XX will drive SCDIO low to

acknowledge the address byte and to indicate

that it is ready for a read operation. If an

acknowledge is not sent by the CS493XX, a

stop condition should be issued and the read

sequence should be restarted.

5) The data is ready to be clocked out on the

SCDIO line at this point. Data clocked out by

SEND I2C START:

WRITE ADDRESS BYTE

SET TO 0 FOR WRITE

GET ACK

MORE DATA?

I2C STOP:

WITH MODE BIT

DROP SCDIO LOW

WHILE SCCLK IS HIGH

SEND DATABYTE

GET ACK

RAISE SCDIO HIGH

WHILE SCCLK IS HIGH

Figure 22. I2C® Write Flow Diagram

CS49310 数据表(PDF) 40 Page - Cirrus Logic

CS49310 数据表(HTML) 40 Page - Cirrus Logic

Html Pages

1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 41 42 43 44 45 46 47 48 49 50 51 52 53 54 55 56 57 58 59 60 61 62 63 64 65 66 67 68 69 70 71 72 73 74 75 76 77 78 79 80 81 82 83 84 85 86 87 88 89 90

数据表下载