This menu is used to select the measurement units and con-

figure the system to measure Volume & Level. Refer to page

15 for Level Only applications or page 20 for Flow & Level

applications.

Following is a step-by-step procedure for using the Volume

& Level menu. It is assumed that you are starting from the

RUN mode.

SOFTWARE CONFIGURATION cont.

17

SYSTEM CONFIGURATION MENU—VOLUME AND LEVEL

System Configuration Menu (Volume and Level)

Display

Keystroke

Comment and/or Additional Keystrokes

Magnetrol Int’l

Press ENT

At start up, the unit is in the run mode displaying Magnetrol Int’l. Pressing ENT

xxxx units

allows you to enter the main menu.

Measured Values

Press

Allows you to enter the System Config menu.

ENT to Select

System Config

Press ENT

Enters the first display (Level Units) of System Config menu.

Level Units

If inches are the desired Level Units press

to continue to the next item. To

Inches

Press ENT or

change units, press ENT and

to select Feet, Centimeters, or Meters. Press ENT

to select desired Level Units.

Enter Password

Enter Valid Password

Entering a valid password and pressing ENT sets your unit selection and

(if units changed)

(factory default is 300)

continues on to the next item.

Mode Setup

Press ENT

Then press

then ENT to change to Volume and Level mode.

Level Only

Volume Units

If cubic feet are the desired Volume Units, press

to continue to the next item.

Cubic Feet

Press ENT or

To change units, press ENT and

to select cubic inches, gallons, milliliters, or

liters. Press ENT to select desired Volume Units.

Press ENT,

, then ENT to change present setting. You may select Rectangular,

Vessel Type

Press ENT or

Horiz/Flat, Horiz/Ellip, Horiz/Sphere, Spherical, Verti/Flat, Verti/Ellip, Verti/Sphere,

Rectangular

Verti/Conical or Custom Table (Refer to Figure 12 for Custom Table). If the

present setting is correct (Rectangular), press ENT, input vessel dimensions, and

then press

to continue to next selection.

Radius=

The values requested may vary depending on the type of vessel selected. Refer

xxxx units

Enter value and press ENT

to vessel drawing for proper dimensions.

(Vessel Dependent)

Width=

The values requested may vary depending on the type of vessel selected. Refer

xxxx units

Enter value and press ENT

to vessel drawing for proper dimensions.

(Vessel Dependent)

Length=

The values requested may vary depending on the type of vessel selected. Refer

xxxx units

Enter value and press ENT

to vessel drawing for proper dimensions.

(Vessel Dependent)

Range Setting

Press ENT or

Press ENT to change the range setting. If setting is correct, press

to continue

xxxx units

to Span Settings.

NOTE: It is recommended to use Manual Set (as opposed to Auto Set) when changing the range or span settings.

Press ENT to manually set the range setting. An

will appear in the bottom line

Manual Set

Press ENT or

of the display. This allows you to change the range value. Measure the distance

xxxx units

from the face of the transducer to the maximum distance to be measured. Enter

value and press ENT. If Auto Set is preferred press

.

The liquid surface must be at the maximum distance to be measured. Check to

Auto Set (If chosen)

Press ENT or

see that the distance being displayed is correct. When you press the ENT key,

xxxx units

that distance will be set as your range and the program will continue on to the

next selection. To continue without making changes press

.

NOTE: The span value is automatically set ONLY when the entered range value has decreased from its previous value.

Span Setting

Value shown will be 18 inches less than the range setting. This is the maximum

xxxx units

Press ENT or

span value available. To reduce the span press ENT. If the present setting is

correct press

to continue to Previous Menu.

Manual Set

Press ENT to manually set the span setting. Measure the distance from the

xxxx units

Press ENT or

maximum range that was set to the highest point to be measured. Enter value

and press ENT. If Auto Set is preferred press

.

The liquid surface must be at the highest level to be measured. Check to see

Auto Set (If chosen)

Press ENT or

that the level being displayed is correct. When you press the ENT key, that

xxxx units

measurement will be set as your span and the program will continue on to the

next selection. To continue without changes press

.

Previous Menu

Press ENT

Pressing the ENT key will set all values and return to System Config. Press DEL

ENT to select

to return to the run mode.