ST10F271 datasheet(40/173 Pages) STMICROELECTRONICS

40 / 173 page

Internal Flash memory

ST10F271

40/173

Then the operation can be resumed in the following way:

FCR0H

|= 0x0800;

/*Set SER in FCR0H*/

FCR0H

|= 0x8000;

/*Operation resume*/

Before resuming a suspended Erase, FCR1H/FCR1L must be read to check if the Erase is

already completed (FCR1H = FCR1L = 0x0000 if Erase is complete). Original setup of

Select Operation bits in FCR0H/L must be restored before the operation resume, otherwise

the operation is aborted and bit RESER of FER is set.

Erase suspend, program and resume

A Sector Erase operation can be suspended in order to program (Word or Double Word)

another Sector.

Example: Sector Erase of sector B0F1 of IFLASH Module.

FCR0H

|= 0x0800;

/*Set SER in FCR0H*/

FCR1L

|= 0x0002;

/*Set B0F1*/

FCR0H

|= 0x8000;

/*Operation start*/

Example: Sector Erase Suspend.

FCR0H

|= 0x4000;

/*Set SUSP in FCR0H*/

/*Loop to wait for LOCK=0 and WMS=0*/

{tmp1

= FCR0L;

tmp2

= FCR0H;

} while ((tmp1 && 0x0010) || (tmp2 && 0x8000));

Example: Word Program of data 0x5555AAAA at address 0x045554 in IFLASH module.

FCR0H

&= 0xBFFF;

/*Rst SUSP in FCR0H*/

FCR0H|= 0x2000;/*Set WPG in FCR0H*/

FARL

= 0x5554;

/*Load Add in FARL*/

FARH

= 0x0004;

/*Load Add in FARH*/

FDR0L

= 0xAAAA;

/*Load Data in FDR0L*/

FDR0H

= 0x5555;

/*Load Data in FDR0H*/

FCR0H

|= 0x8000;

/*Operation start*/

Once the Program operation is finished, the Erase operation can be resumed in the

following way:

FCR0H|= 0x0800;/*Set SER in FCR0H*/

FCR0H|= 0x8000;/*Operation resume*/

Notice that during the Program Operation in Erase suspend, bits SER and SUSP are low. A

Word or Double Word Program during Erase Suspend cannot be suspended.

In summary:

A Sector Erase can be suspended by setting SUSP bit.

●

To perform a Word Program operation during Erase Suspend, firstly bits SUSP and

SER must be reset, then bit WPG and WMS can be set.

●

To resume the Sector Erase operation bit SER must be set again.

●

In any case it is forbidden to start any write operation with SUSP bit already set.

Set protection

Example 1: Enable Write Protection of sectors B0F3-0 of Bank 0 in IFLASH module.

ST10F271 数据表(PDF) 40 Page - STMicroelectronics

ST10F271 数据表(HTML) 40 Page - STMicroelectronics

Html Pages

1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 41 42 43 44 45 46 47 48 49 50 51 52 53 54 55 56 57 58 59 60 61 62 63 64 65 66 67 68 69 70 71 72 73 74 75 76 77 78 79 80 81 82 83 84 85 86 87 88 89 90 91 92 93 94 95 96 97 98 99 100 ...More

数据表下载

链接网址

ST10F271 数据表(PDF) 40 Page - STMicroelectronics

ST10F271 数据表(HTML) 40 Page - STMicroelectronics

Html Pages

1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 41 42 43 44 45 46 47 48 49 50 51 52 53 54 55 56 57 58 59 60 61 62 63 64 65 66 67 68 69 70 71 72 73 74 75 76 77 78 79 80 81 82 83 84 85 86 87 88 89 90 91 92 93 94 95 96 97 98 99 100 ...More

数据表 下载

链接网址

数据表下载