PIC16F1507-ESLASHSS. datasheet(137/278 Pages) MICROCHIP

137 / 278 page

 2011-2015 Microchip Technology Inc.

DS40001586D-page 137

PIC16(L)F1507

17.5.2.1

T1G Pin Gate Operation

The T1G pin is one source for Timer1 gate control. It

can be used to supply an external source to the Timer1

gate circuitry.

17.5.2.2

Timer0 Overflow Gate Operation

When Timer0 increments from FFh to 00h, a low-to-

high pulse will automatically be generated and inter-

nally supplied to the Timer1 gate circuitry.

17.5.3

TIMER1 GATE TOGGLE MODE

When Timer1 Gate Toggle mode is enabled, it is possi-

ble to measure the full-cycle length of a Timer1 gate

signal, as opposed to the duration of a single level

pulse.

The Timer1 gate source is routed through a flip-flop that

changes state on every incrementing edge of the sig-

nal. See Figure 17-4 for timing details.

Timer1 Gate Toggle mode is enabled by setting the

T1GTM bit of the T1GCON register. When the T1GTM

bit is cleared, the flip-flop is cleared and held clear. This

is necessary in order to control which edge is

measured.

17.5.4

TIMER1 GATE SINGLE-PULSE

MODE

When Timer1 Gate Single-Pulse mode is enabled, it is

possible to capture a single pulse gate event. Timer1

Gate Single-Pulse mode is first enabled by setting the

T1GSPM bit in the T1GCON register. Next, the T1GGO/

DONE bit in the T1GCON register must be set. The

Timer1 will be fully enabled on the next incrementing

edge. On the next trailing edge of the pulse, the T1GGO/

DONE bit will automatically be cleared. No other gate

events will be allowed to increment Timer1 until the

T1GGO/DONE bit is once again set in software. See

Figure 17-5 for timing details.

If the Single Pulse Gate mode is disabled by clearing the

T1GSPM bit in the T1GCON register, the T1GGO/DONE

bit should also be cleared.

Enabling the Toggle mode and the Single-Pulse mode

simultaneously will permit both sections to work

together. This allows the cycle times on the Timer1 gate

source to be measured. See Figure 17-6 for timing

details.

17.5.5

TIMER1 GATE VALUE STATUS

When Timer1 Gate Value Status is utilized, it is possible

to read the most current level of the gate control value.

The value is stored in the T1GVAL bit in the T1GCON

gate is not enabled (TMR1GE bit is cleared).

17.5.6

TIMER1 GATE EVENT INTERRUPT

When Timer1 Gate Event Interrupt is enabled, it is pos-

sible to generate an interrupt upon the completion of a

gate event. When the falling edge of T1GVAL occurs,

the TMR1GIF flag bit in the PIR1 register will be set. If

the TMR1GIE bit in the PIE1 register is set, then an

interrupt will be recognized.

The TMR1GIF flag bit operates even when the Timer1

gate is not enabled (TMR1GE bit is cleared).

Note:

Enabling Toggle mode at the same time

as changing the gate polarity may result in

indeterminate operation.

PIC16F1507-E/SS. 数据表(PDF) 137 Page - Microchip Technology

PIC16F1507-E/SS. 数据表(HTML) 137 Page - Microchip Technology

Html Pages

1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 41 42 43 44 45 46 47 48 49 50 51 52 53 54 55 56 57 58 59 60 61 62 63 64 65 66 67 68 69 70 71 72 73 74 75 76 77 78 79 80 81 82 83 84 85 86 87 88 89 90 91 92 93 94 95 96 97 98 99 100 ...More

数据表下载