WM8904ECSSLASHR datasheet(34/188 Pages) WOLFSON

34 / 188 page

WM8904

Pre-Production

PP, Rev 3.3, September 2012

DEVICE DESCRIPTION

INTRODUCTION

The WM8904 is a high performance ultra-low power stereo CODEC optimised for portable audio

applications. Flexible analogue interfaces and powerful digital signal processing (DSP) make it ideal

for small portable devices.

The WM8904 supports up to 6 analogue audio inputs. One pair of single-ended or differential

microphone/line inputs is selected as the ADC input source. An integrated bias reference is provided

to power standard electret microphones.

A two-channel digital microphone interface is also supported, with direct input to the DSP core

bypassing the ADCs.

One pair of ground-reference Class-W headphone outputs is provided; these are powered from an

integrated Charge Pump, enabling high quality, power efficient headphone playback without any

requirement for DC blocking capacitors. A DC Servo circuit is available for DC offset correction,

thereby suppressing pops and reducing power consumption. Two line outputs are provided; these are

also capable of driving ear speakers and stereo headsets. Ground loop feedback is available on the

headphone outputs and the line outputs, providing rejection of noise on the ground connections. All

outputs use Wolfson SilentSwitch™ technology for pop and click suppression.

The stereo ADCs and DACs are of hi-fi quality, using a 24-bit low-order oversampling architecture to

deliver optimum performance. A flexible clocking arrangement supports mixed ADC and DAC sample

rates, whilst an integrated ultra-low power FLL provides additional flexibility. A high pass filter is

available in the ADC path for removing DC offsets and suppressing low frequency noise such as

mechanical vibration and wind noise. A digital mixing path from the ADC to the DAC provides a

sidetone of enhanced quality during voice calls. DAC soft mute and un-mute is available for pop-free

music playback.

The integrated Dynamic Range Controller (DRC) and ReTuneTM Mobile 5-band parametric equaliser

(EQ) provide further processing capability of the digital audio paths. The DRC provides compression

and signal level control to improve the handling of unpredictable signal levels. ‘Anti-clip’ and ‘quick

release’ algorithms improve intelligibility in the presence of transients and impulsive noises. The EQ

provides the capability to tailor the audio path according to the frequency characteristics of an

earpiece or loudspeaker, and/or according to user preferences.

The WM8904 has a highly flexible digital audio interface, supporting a number of protocols, including

I2S, DSP, MSB-first left/right justified, and can operate in master or slave modes. PCM operation is

supported in the DSP mode. A-law and

-law companding are also supported. Time division

multiplexing (TDM) is available to allow multiple devices to stream data simultaneously on the same

bus, saving space and power.

The system clock SYSCLK provides clocking for the ADCs, DACs, DSP core, digital audio interface

and other circuits. SYSCLK can be derived directly from the MCLK pin or via an integrated FLL,

providing flexibility to support a wide range of clocking schemes. Typical portable system MCLK

frequencies, and sample rates from 8kHz to 48kHz are all supported. The clocking circuits are

configured automatically from the sample rate (fs) and from the SYSCLK / fs ratio.

The integrated FLL can be used to generate SYSCLK from a wide variety of different reference

sources and frequencies. The FLL can accept a wide range of reference frequencies, which may be

high frequency (e.g. 13MHz) or low frequency (eg. 32.768kHz). The FLL is tolerant of jitter and may

be used to generate a stable SYSCLK from a less stable input signal. The integrated FLL can be

used as a free-running oscillator, enabling autonomous clocking of the Charge Pump and DC Servo if

required.

The WM8904 uses a standard 2-wire control interface, providing full software control of all features,

together with device register readback. An integrated Control Write Sequencer enables automatic

scheduling of control sequences; commonly-used signal configurations may be selected using ready-

programmed sequences, including time-optimised control of the WM8904 pop suppression features.

It is an ideal partner for a wide range of industry standard microprocessors, controllers and DSPs.

Unused circuitry can be disabled under software control, in order to save power; low leakage currents

enable extended standby/off time in portable battery-powered applications.

WM8904ECS/R 数据表(PDF) 34 Page - Wolfson Microelectronics plc

WM8904ECS/R 数据表(HTML) 34 Page - Wolfson Microelectronics plc

Html Pages

1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 41 42 43 44 45 46 47 48 49 50 51 52 53 54 55 56 57 58 59 60 61 62 63 64 65 66 67 68 69 70 71 72 73 74 75 76 77 78 79 80 81 82 83 84 85 86 87 88 89 90 91 92 93 94 95 96 97 98 99 100 ...More

数据表下载