 |
数据搜索系统，热门电子元器件搜索 |
|
|
数据搜索系统，热门电子元器件搜索 |
|
WM8940CGEFL/RV 数据表(PDF) 49 Page - Wolfson Microelectronics plc |
|
|
|||||||||||||||||||||||||||||
WM8940CGEFL/RV 数据表(HTML) 49 Page - Wolfson Microelectronics plc |
|
|
49 / 91 page  Production Data WM8940 w PD, Rev 4.3, November 2011 49 REGISTER ADDRESS BIT LABEL DEFAULT DESCRIPTION R56 Mono mixer control 7 MONOATTN 0 Attenuation control for bypass path (output of input boost stage) to mono mixer input 0 = 0dB 1 = -10dB 6 MONOMUTE 0 0=No mute 1=Output muted. During mute the mono output will output VMID which can be used as a DC reference for a headphone out. 2 AUX2MONO 0 Output of Auxilary amplifier to mono mixer input: 0 = not selected 1 = selected 1 BYP2MONO 0 Bypass path (output of input boost stage) to mono mixer input 0 = non selected 1 = selected 0 DAC2MONO 0 Output of DAC to mono mixer input 0 = not selected 1 = selected Table 37 Mono Mixer Control ENABLING THE OUTPUTS Each analogue output of the WM8940 can be separately enabled or disabled. The analogue mixer associated with each output has a separate enable. All outputs are disabled by default. To save power, unused parts of the WM8940 should remain disabled. Outputs can be enabled at any time, but it is not recommended to do so when BUFIO is disabled (BUFIOEN=0), as this may cause pop noise (see “POP Minimisation” section). REGISTER ADDRESS BIT LABEL DEFAULT DESCRIPTION R1 Power management 1 3 BIASEN 0 Analogue amplifiers bias enable 2 BUFIOEN 0 VMID buffer enable R3 Power management 3 7 MONOEN 0 MONOOUT enable 6 SPKNEN 0 SPKOUTN enable 5 SPKPEN 0 SPKOUTP enable 3 MONOMIXEN 0 Mono mixer enable 2 SPKMIXEN 0 Speaker Mixer enable Note: All “Enable” bits are 1 = ON, 0 = OFF Table 38 Output Stages Power Management Control UNUSED ANALOGUE INPUTS/OUTPUTS Whenever an analogue input/output is disabled, it remains connected to AVDD/2 through a resistor. This helps to prevent pop noise when the output is re-enabled. The resistance between the voltage buffer and the output pins can be controlled using the VROI control bit. The default impedance is low, so that any capacitors on the outputs can charge up quickly at start-up. If a high impedance is desired for disabled outputs, VROI can then be set to 1, increasing the resistance to about 30k . |
|
链接网址 |
| ALLDATASHEET是否为您带来帮助? [ DONATE ] |
关于 Alldatasheet | 广告服务 | 联系我们 | 隐私政策 | 数据表链接 | 链接交换 | 制造商名单 All Rights Reserved©Alldatasheet.com |
| Russian : Alldatasheetru.com | Korean : Alldatasheet.co.kr | Spanish : Alldatasheet.es | French : Alldatasheet.fr | Italian : Alldatasheetit.com Portuguese : Alldatasheetpt.com | Polish : Alldatasheet.pl | Vietnamese : Alldatasheet.vn Indian : Alldatasheet.in | Mexican : Alldatasheet.com.mx | British : Alldatasheet.co.uk | New Zealand : Alldatasheet.co.nz |
|
Family Site : ic2ic.com |
icmetro.com |
Chinese ▼
English
Chinese
German
Japanese
Russian
Korean
Spanish
French
Italian
Portuguese
Polish
Vietnamese
Indian
Mexican
British
New Zealand
