LAN9211 datasheet(92/147 Pages) SMSC

92 / 147 page

High-Performance Small Form Factor Single-Chip Ethernet Controller with HP Auto-MDIX Support

Datasheet

Revision 2.9 (03-01-12)

SMSC LAN9211

DATASHEET

5.3.13

PMT_CTRL— Power Management Control Register

This register controls the Power Management features. This register can be read while the

LAN9211

is in a power saving mode.

Note: The LAN9211 must always be read at least once after power-up, reset, or upon return from a

power-saving state or write operations will not function.

Offset:

84h

Size:

32 bits

BITS

DESCRIPTION

TYPE

DEFAULT

31:14

RESERVED

13-12

Power Management Mode (PM_MODE)

– These bits set the LAN9211 into

the appropriate Power Management mode. Special care must be taken when

modifying these bits.

Encoding:

00b – D0 (normal operation)

01b – D1 (wake-up frame and magic packet detection are enabled)

10b – D2 (can perform energy detect)

11b – RESERVED - Do not set in this mode

Note:

When the LAN9211 is in any of the reduced power modes, a write

of any data to the BYTE_TEST register will wake-up the device. DO

NOT PERFORM WRITES TO OTHER ADDRRESSES while the

READY bit in this register is cleared.

00b

RESERVED

PHY Reset (PHY_RST) – Writing a ‘1’ to this bit resets the PHY. The internal

logic automatically holds the PHY reset for a minimum of 100us. When the

PHY is released from reset, this bit is automatically cleared. All writes to this

bit are ignored while this bit is high.

Wake-On-Lan Enable (WOL_EN) – When set, the PME signal (if enabled

with PME_EN) will be asserted in accordance with the PME_IND bit upon a

WOL event. When set, the PME_INT will also be asserted upon a WOL

event, regardless of the setting of the PME_EN bit.

R/W

Energy-Detect Enable (ED_EN) - When set, the PME signal (if enabled with

PME_EN) will be asserted in accordance with the PME_IND bit upon an

Energy-Detect event. When set, the PME_INT will also be asserted upon an

Energy Detect event, regardless of the setting of the PME_EN bit.

R/W

RESERVED

PME Buffer Type (PME_TYPE) – When cleared, enables PME to function

as an open-drain buffer for use in a Wired-Or configuration. When set, the

PME output is a Push-Pull driver. When configured as an open-drain output

the PME_POL field is ignored, and the output is always active low.

R/W

NASR

LAN9211 数据表(PDF) 92 Page - SMSC Corporation

LAN9211 数据表(HTML) 92 Page - SMSC Corporation

Html Pages

1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 41 42 43 44 45 46 47 48 49 50 51 52 53 54 55 56 57 58 59 60 61 62 63 64 65 66 67 68 69 70 71 72 73 74 75 76 77 78 79 80 81 82 83 84 85 86 87 88 89 90 91 92 93 94 95 96 97 98 99 100 ...More

数据表下载

链接网址

LAN9211 数据表(PDF) 92 Page - SMSC Corporation

LAN9211 数据表(HTML) 92 Page - SMSC Corporation

Html Pages

1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 41 42 43 44 45 46 47 48 49 50 51 52 53 54 55 56 57 58 59 60 61 62 63 64 65 66 67 68 69 70 71 72 73 74 75 76 77 78 79 80 81 82 83 84 85 86 87 88 89 90 91 92 93 94 95 96 97 98 99 100 ...More

数据表 下载

链接网址

数据表下载